Low Voltage Cable Jointer in UAE

<section><p class="heading jdMain">Job Description</p><p class="heading">Roles &amp; Responsibilities</p><div class="paragraph"><ol><li><p>Install, terminate, test, and commission Low Voltage (LV) electrical systems.</p></li><li><p>Install power and lighting systems, distribution boards (DBs), panel boards, and switchgear.</p></li><li><p>Carry out cable laying, cable pulling, glanding, dressing, and termination.</p></li><li><p>Install cable trays, trunking, conduits, raceways, and containment systems.</p></li><li><p>Install and connect sockets, switches, light fixtures, isolators, and electrical accessories.</p></li><li><p>Perform electrical testing, continuity checks, insulation resistance tests, and troubleshooting.</p></li><li><p>Read and interpret electrical drawings, layouts, and single-line diagrams.</p></li><li><p>Coordinate with supervisors, engineers, and other trades to ensure smooth project execution.</p></li><li><p>Ensure compliance with project specifications, approved shop drawings, and local regulations.</p></li><li><p>Maintain tools, equipment, and work areas in a safe and organized condition.</p></li><li><p>Report defects, material shortages, and installation issues to the supervisor.</p></li><li><p>Attend testing and commissioning activities and rectify punch-list items.</p></li><li><p>Follow all HSE policies and electrical safety procedures.</p></li></ol></div></section><section><p class="heading">Desired Candidate Profile</p><p class="paragraph"></p><p>Qualifications</p><ul><li><p>ITI / Diploma / Technical Certificate in Electrical Engineering or Electrician Trade.</p></li><li><p>Relevant electrical trade certification is preferred.</p></li></ul><br><p>Experience</p><ul><li><p>Minimum <strong>3–5 years</strong> of experience as an Electrician in building construction projects.</p></li><li><p>GCC/UAE construction experience is preferred.</p></li><li><p>Experience in <strong>high-rise residential towers, commercial buildings, hotels, villas, hospitals, or mixed-use developments</strong>.</p></li><li><p>Experience working with MEP contractors or main contractors is an advantage.</p></li></ul><br><p>Preferred Knowledge</p><ul><li><p>UAE Electrical Regulations</p></li><li><p>DEWA / ADDC / AADC project experience (preferred)</p></li><li><p>Testing &amp; Commissioning support</p></li><li><p>Electrical quality standards</p></li><li><p>Building construction practices</p></li></ul><p></p></section>

<h2 class="h5">Job description</h2> <div class="t-break" data-jb-field="description"> <b>Job Description</b>Overview<p>As a Resident Engineer – Cables, you will lead and oversee the execution of underground cable infrastructure projects, ensuring all civil works are delivered in line with design specifications, quality standards, and health, safety, and environmental requirements. You will act as the primary on-site representative, coordinating contractors, consultants, and stakeholders to ensure efficient delivery of high-voltage cable systems within schedule and budget.</p><br>Your role<ul><li>Lead and supervise the construction of underground cable projects, including trenching, duct banks, cable laying, joint bays, and associated civil works.</li><li>Ensure all works are executed in accordance with approved drawings, specifications, and project standards.</li><li>Monitor contractor performance, progress, and compliance with quality and HSE requirements.</li><li>Review and approve contractor submissions such as method statements, shop drawings, and material submittals.</li><li>Conduct regular site inspections and enforce QA/QC procedures throughout project execution.</li><li>Coordinate with electrical, mechanical, and utility teams to ensure seamless integration of cable systems.</li><li>Act as the primary liaison between client, contractor, and supervision team on-site.</li><li>Identify and resolve technical issues, construction challenges, and contractual matters.</li><li>Manage project schedules, monitor progress, and implement corrective actions where required.</li><li>Maintain detailed site documentation, reports, and records of project activities.</li><li>Lead site meetings, progress reviews, and communicate project status, risks, and mitigation plans.</li><li>Oversee testing, commissioning support, and final handover of cable infrastructure works.</li></ul>About you<ul><li>Bachelor’s degree in Civil Engineering or a related discipline.</li><li>10+ years of experience in infrastructure or utility projects, with strong experience in underground cable works.</li><li>Proven experience in managing and supervising high-voltage cable or utility infrastructure projects.</li><li>Strong knowledge of construction methodologies, QA/QC practices, and HSE regulations.</li><li>Familiarity with international standards and GCC/UAE regulations is highly desirable.</li><li>Demonstrated leadership and team management capabilities.</li><li>Excellent communication, reporting, and stakeholder management skills.</li><li>Strong analytical, problem-solving, and decision-making abilities.</li><li>Proficiency in MS Office and project management tools; knowledge of Primavera or MS Project is an advantage.</li><li>Ability to work on-site and travel within the region as required.</li></ul><span>Rewards &amp; benefits</span><p><span>Explore the rewards and benefits that help you thrive – at every stage of your life and your career.</span></p><br><p><span>This includes:</span></p><br><ul><li>Tax-free salary.</li><li>Life insurance coverage.</li><li>Medical insurance.</li><li>Annual leave balance.</li><li>Company gratuity scheme.</li><li>Discretionary bonus program.</li><li>Annual flight contribution.</li><li>Transportation &amp; housing allowances.</li><li>Employee Wellbeing Program: 24/7 access to specialists in finance, legal matters, family care, personal health, fitness, and nutrition.</li></ul><p><span>Seize every opportunity to sharpen your skills, expand your expertise, and be recognized for the impact you make.</span></p><br><span>About AtkinsRéalis</span><p><span>We're AtkinsRéalis, a world-class engineering services and nuclear organization. We connect people, data and technology to transform the world's infrastructure and energy systems. Together, with our industry partners and clients, and our global team of consultants, designers, engineers and project managers, we can change the world. We're committed to leading our clients across our various end markets to engineer a better future for our planet and its people. </span></p><br><p><span>Find out more.</span></p><br><b>Worker Type</b>Employee<b>Job Type</b>Regular<p><span><i>At </i></span> <i><span>AtkinsRéalis</span></i><span><i>, we seek to hire individuals with diverse characteristics, backgrounds and perspectives. We strongly believe that world-class talent makes no distinctions based on gender, ethnic or national origin, sexual identity and orientation, age, religion or disability, but enriches itself through these differences. &nbsp;</i></span></p><br> </div>

<h2 class="h5">Job description</h2> <div class="t-break" data-jb-field="description"> <span>Siemens strongly believes in the value of a Digital Portfolio, hence Smart Infrastructure combines Digital Power Distribution and Digital Building Infrastructure technologies. Our Digital Portfolio will enable our customers to enjoy occupant’s intuitive buildings which are comfortable, safe, secure and energy efficient. Smart infrastructure thoughtfully connects energy systems, buildings and industries to adapt and evolve the way we live and work. We work together with customers and partners to build an ecosystem that intuitively responds to the needs of people and helps customers to better use resources. It helps our customers to thrive, communities to progress and supports sustainable development. We are looking for a Senior Project Engineer, who is responsible to independently handling the Modification, Extension, Maintenance and Spare parts orders of Siemens make MV and LV Switchgears. Having sound technical knowledge of Siemens MV Switchgears (both GIS and AIS) and LV Switchgears. Well versed in Project Management processes starting from Sales handover until project completion. Aware of Project opening and clarifications, Communication, Organizing, Planning, Executing, Monitoring &amp; Controlling the project activities. Having 10 yrs of experience in handling similar projects. Join our Smart Infrastructure as the Senior Project Engineer – MV &amp; LV Switchgear and Protection Systems and help us re-imagine the world by finding solutions and making the world a more inquisitive place for tomorrow. You‘ll make a difference by • Assisting Project Manager in managing Switchgear projects within the time, budget and quality requirements. • Must have sound technical knowledge of Siemens make Medium Voltage Switchgears (both AIS &amp; GIS) and their Protection Systems. especially in the Utility substations and Oil and Gas industries. • Project Planning: Taking over project from Sales team, make clarifications and perform overall project planning including preparing Project Overview, Resource allocation plan, Procurement plan, Revenue generation plan and overall Project time schedule. • Procurement and Subcontracting: Release Purchase Orders and Subcontracts after taking inputs from Engineering and Procurement teams. Make regular follow-ups with vendors and suppliers for their deliverables until project completion. • Project Monitoring and Controlling: Analyze and continuously monitor project plan fulfilment with regard to technical and commercial aspects of the project. Prepare Project Progress Measurement sheets, conduct weekly review meetings. Assist Project manager in monitoring cash-flow and revenue generation planning and activate appropriate escalation procedures. • Project Reporting: Assess and document project status and perform project internal and external reporting in line with Company and Customer guidelines. • Risk Management: Carry out risks assessment of the project from Sales handover phase until project completion, identify risks and prepare mitigation action plan. Continuously monitor the risk-influencing factors and take appropriate measures. • Contracts &amp; Claim Management: Assist Project and Procurement Manager in Identifying early deviations and changes in project. Send timely change notifications to Customer and suppliers. Assist Project Manager in preparing Change orders and Time extension Claims. • Stakeholder Management &amp; Customer relations: Assist Project Manager in developing stakeholder management plan and engage all parties accordingly. Inform project status to customer, internal management, project team and other interested parties (Stakeholders) on a regular basis. Develop strategies to continue and/ or reinforce engagements to the customer. Gather actively opinions as well as suggestions from the customer and the additional interested parties (Stakeholder) and develop/ facilitate/ support an open, professional relation to the customer and to additional stakeholders. Perform customer satisfaction feedback survey at the end of the project. • Project Closeout: Manage the Project completion/ close out and the acceptance of delivery units and services incl. validation and verification and organize the finalized handover to the customer and involved parties. Conduct Lesson Learned Workshop for the project and record and circulate the results. Your success is grounded in • Bachelor’s Degree in Electrical Engineering • Minimum 10 years of Site Testing and Commissioning experience on Siemens make Medium Voltage Air and Gas insulated Switchgears (GIS) and protection system in Utility substations and oil and Gas Industry. Advance knowledge and experience of handling Service Level Agreements (SLA) and maintenance / retrofitting projects as project manager. • Expert knowledge of Medium and Low voltage Switchgears and protection systems • PMP or IPMA certification is a plus • Experience in turn-key projects with direct interface to the customer/ public authorities/ subcontractor Additional Skills: • Problem solving skills • Excellent communication skills • Team Player • Negotiation skills • Leadership • Initiative • Result driven We offer you • 2 to 3 days of remote working per week, as a global standard. • Diverse and inclusive culture. • An environment where everyone can bring their whole self and feel a sense of belonging. • the foundation to develop personally and expertly. • Great variety of learning &amp; development opportunities Create a better #TomorrowWithUs! If you are a motivated teammate, eager to learn new things and looking to grow your career in a strong and forward-thinking company, hit apply!. Siemens is dedicated to quality, equality, and valuing diversity, and we encourage applications that reflect the diversity of the communities within which we work. Siemens is an equal opportunities employer and do not discriminate unlawfully on any grounds. We are committed to providing access, equal opportunity and reasonable accommodation for individuals with disabilities in employment, its services, programs, and activities. At Siemens, we are always challenging ourselves to build a better future. We need the most innovative and diverse Digital Minds to develop tomorrow ‘s reality. Find out more about the Digital world of Siemens here: www.siemens.com/careers/digitalminds Please note: Only complete applications can be considered in the selection process. #UAEJobs</span> </div>

<h2 class="h5">Job description</h2> <div class="t-break" data-jb-field="description"> <span>Job Title: Commissioning Engineer (MV/LV Switchgear &amp; Protection) Location: Abu Dhabi, UAE Commissioning Engineer –Abu Dhabi, UAE We know that a business only thrives if our people are thriving. That’s why we always put our people first. Our global and diverse team would be happy to support you and challenge you to grow in many ways. Who knows where our joint journey will take you? Siemens strongly believes in the value of a Digital Portfolio; hence Smart Infrastructure combines Digital Power Distribution and Digital Building Infrastructure technologies. Our Digital Portfolio will enable our customers to enjoy occupants’ intuitive buildings which are comfortable, safe, secure and energy efficient. Smart infrastructure thoughtfully connects energy systems, buildings and industries to adapt and evolve the way we live and work. We work together with customers and partners to build an ecosystem that intuitively responds to the needs of people and helps customers to better use resources. It helps our customers to thrive, communities to progress and supports sustainable development. Join our Smart Infrastructure Customer Service Team as Utilities / Oil &amp; Gas Substations MV / LV Switchgear &amp; Protection Commissioning Engineer. You ‘ll make a difference by Installation, Testing &amp; Commissioning of electrical power system equipment such as MV / LV Switchgears, Protection Relays, Control &amp; Protection Panels etc. in power plants and substations (Utilities, O&amp;G and Industrial Market) Conducting testing &amp; commissioning of MV/LV switchgears, Power &amp; Distribution Transformers, Current Transformers, Voltage Transformers and various types of Main / Back up / Bus bar Protection relays. Fault Trouble shooting and Analysis for Switchgears, Protection Relays / Systems Preparing Method Statement, preparation of NCR / Incident / RCA reports etc. Supporting Engineering Manager, project manager for site planning and execution topics before site mobilization Training of Operating Personnel at site for commissioned Electrical Equipment Following HSE principles and guidelines is a must. Show responsibility at site by adhering to HSE of Siemens / Main contractor. Your Qualifications and Skills Bachelor Engineering degree from local or international University or Technical Institute in Electrical / Electronic Engineering disciplines You Bring with a proven experience working in Utilities, Oil and Gas Industry Min 5 years’ hands-on experience with Installation, testing &amp; commissioning of MV/LV switchgears, Power &amp; Distribution Transformers, Current Transformers, Voltage Transformers, and various types of Main / Back up / Bus bar Protection relays. In depth knowledge on Protection schemes / Relays including testing &amp; commissioning of Overcurrent, Earth fault, Line Differential, Line Distance, Transformer Differential / REF, Under frequency and LIBBP / HIBBP relays in Utility and O&amp;G sectors with 100% success. Medium Voltage Switchgear &amp; Protection Schemes, Line Differential Protection, Transformer Protection, Bus Bar Protection etc. Familiar with OMICRON Secondary Injection test Kit CMC356 / CMC500, Different OMICRON Test Modules such as Quick CMC, State Sequencer, Ramping, Distance, Differential, Advanced Distance, Differential etc. Knowledge of different Communication Protocols especially IEC61850 Preparing DIGSI Projects for Protection &amp; Control Application for Medium Voltage Systems. Technical Product knowhow, Relay Communication Software, IEC61850 Communication, GOOSE Applications, Preparation of Control Logics in BCPU / BCU, creation of scd / icd / cid files, knowledge on other Communication Protocols. Experience with different manufacturer protection relays will be an added advantage. Other requirements Open to travel within the middle east region Result driven team player. Good communication skills in English language (written and spoken) with the ability to work in a team environment. We offer you Diverse and inclusive culture. An environment where everyone can bring their whole self and feel a sense of belonging. the foundation to develop personally and expertly. Great variety of learning &amp; development opportunities Create a better #TomorrowWithUs! If you are a motivated teammate, eager to learn new things and looking to grow your career in a strong and forward-thinking company, hit apply! Siemens is dedicated to quality, equality, and valuing diversity, and we encourage applications that reflect the diversity of the communities within which we work. Siemens is an equal opportunities employer and do not discriminate unlawfully on any grounds. We are committed to providing access, equal opportunity and reasonable accommodation for individuals with disabilities in employment, its services, programs, and activities. At Siemens, we are always challenging ourselves to build a better future. We need the most innovative and diverse Digital Minds to develop tomorrow ‘s reality. Find out more about the Digital world of Siemens here: www.siemens.com/careers/digitalminds Please note: Only complete applications can be considered in the selection process. #UAEJobs</span> </div>

<p>Help us build the future and we’ll help you build a rewarding and purposeful career. Our global network is made up of architects, designers, planners, engineers, and environmental scientists all working towards the same goal. We are inviting applications and expressions of interest from Engineers to join our growing Middle East team. Opportunities Available - Electrical Design Engineer - Senior Electrical Design Engineer - ELV Design Engineer - Senior ELV Design Engineer What You'll Do - Design electrical and ELV systems - Prepare detailed drawings, schematics, and layouts using AutoCAD, Revit, and Navisworks. - Conduct electrical calculations: load analysis, short-circuit analysis, voltage drop, and cable sizing. - Ensure compliance with DEWA, ADDC, UAE Fire Code, and other authority requirements. - Coordinate with other disciplines (MEP, architectural, infrastructure) during design phases. - Support tender documentation and technical specifications. - Liaise with suppliers and contractors to ensure design integrity and execution. What You'll Bring - Bachelor’s degree in electrical engineering. - Demonstrable experience in electrical or ELV design, preferably in the UAE. - Proficiency in AutoCAD, Revit, and electrical design software. - Familiarity with DEWA, ADDC, and UAE regulatory standards. - Strong analytical and problem-solving skills. - Excellent communication and coordination abilities. - Proficiency in electrical design software such as AutoCAD Electrical, EPLAN, SolidWorks Electrical, or similar. - Knowledge of embedded systems, control systems, and power distribution. Express Your Interest If you're ready to play a key role in the future of GHD Middle East's Engineering Teams, we'd love to hear from you. Please submit your CV and a cover letter outlining your experience and interest in joining GHD. This is an Expression of Interest campaign and future appointments may be dependent on upcoming project and panel opportunities. Our Hybrid Work Model Be part of a workplace that combines collaboration, flexibility, and connection. Join us in the office three days per week to contribute, connect and excel in our vibrant environment.</p><p>- Bachelor’s degree in electrical engineering. - Demonstrable experience in electrical or ELV design, preferably in the UAE. - Proficiency in AutoCAD, Revit, and electrical design software. - Familiarity with DEWA, ADDC, and UAE regulatory standards. - Strong analytical and problem-solving skills. - Excellent communication and coordination abilities. - Proficiency in electrical design software such as AutoCAD Electrical, EPLAN, SolidWorks Electrical, or similar. - Knowledge of embedded systems, control systems, and power distribution.</p>

Job Description – Switchgear Specialist (EHV/HV/MV/LV) Job Title: Switchgear Specialist Location: Ruwais Refinery (RR-I, RR-II, RR-III & GUP), Abu Dhabi, UAEProject Duration: 1 Year (Extendable) Work Schedule Monday – Thursday7:00 AM – 5:00 PMFull-Time Onsite<br><br>Job Purpose We are looking for an experienced Switchgear Specialist to support the assessment, troubleshooting, reliability improvement and maintenance of EHV, HV, MV and LV Switchgear systems across ADNOC Refining facilities.<br>The role involves condition assessment, obsolescence review, preventive maintenance, shutdown support and technical recommendations for improving electrical system reliability.<br>Key Responsibilities Perform detailed inspections of HV, MV and LV switchgear. Conduct condition assessments and health monitoring Review recent electrical failures and equipment trips Perform Root Cause Analysis (RCA). Review maintenance history and equipment reliability. Assess End-of-Life equipment and recommend upgrades. Supervise switchgear maintenance during shutdowns. Monitor Partial Discharge (PD) activities. Review SF6 gas systems and circuit breaker mechanisms. Inspect busbars, bus ducts and switchgear assemblies. Review spare parts availability. Prepare technical reports and recommendations. Maintain SAP PM/EAM records. Support emergency breakdown activities.<br>Required Experience Bachelor's Degree in Electrical Engineering. Minimum 15 years of experience in Oil & Gas, Refinery or Petrochemical industries. Extensive experience with:415V Switchgear3.3k V Switchgear11k V Switchgear33k V Switchgear132k V Switchgear220k V Switchgear Hands-on experience with ABB, Siemens, Schneider Electric, Hyundai, Hyosung and L&T switchgear. Strong knowledge of IEC, IEEE and ADNOC electrical standards. Experience with SAP PM/EAM.<br>Preferred ADNOC experience. Shutdown maintenance experience. Condition monitoring and Partial Discharge testing experience.

Job Responsibilities:Development of equipment specification, datasheet, schematic, material requisition Evaluate suppliers’ technical proposal, align proposals to project requirements and prepare technical bid evaluation Supplier’s engineering follow‐up post Contract Award through product design, manufacturing, testing and offshore installation Technical focal point for management of all technical communication with supplier, coordination of documents review, action tracking and closure of TQs, VORs and NCRsExternal interface with Client and Vendors Internal interface with engineering departments (e.g. pipeline, materials, subsea and offshore structures, electrical, telecom, piping, flow assurance, installation), supply chain, quality/HSE and project management Preparation of cost, time, resources estimation Act as discipline lead if required to handle subsea cables and umbilicals packages on multiple projects with direct responsibility of resources management Training and mentoring of younger resources<br>Qualifications And Experience12+ years' experience in subsea power and communication cables and umbilicals Deep knowledge of design, manufacturing and testing of subsea cables and umbilical aspects during various phases of an EPCI project (FEED, bid, detail engineering);Knowledge on relevant codes and standards, regulations and best practices for subsea cables and umbilicals Relevant Engineering Degree (preferably Electrical or Mechanical) Track record of EPCI projects execution for Middle East clients (Saudi Aramco, Qatar Energy, Qatar Energy LNG, ADNOC) Experience with subsea flexible pipes and subsea valves<br>Skills Working under minimum supervision, in a team as well as individually Clear and effective oral and written communications skills Curious and aware of new technologies and developments Willing to share knowledge by mentoring younger resources

<section><p class="heading jdMain">Job Description</p><p class="heading">Roles &amp; Responsibilities</p><div class="paragraph"><p><strong>Site Engineer – Electrical (33kV &amp; 132kV Cabling)</strong></p><p><strong>Experience:</strong> Minimum 5 years in HV cable installation, testing &amp; commissioning, preferably SEWA/DEWA/TAQA certified</p><br><p><strong>Key Responsibilities:</strong></p><ul><li><p>Supervise and execute laying, jointing, and termination of 33kV/132kV HV cables as per SEWA/DEWA/TAQA standards</p></li><li><p>Coordinate cable route surveys, trenching, ducting, and pulling activities on site</p></li><li><p>Oversee HV cable testing (IR, VLF, sheath, partial discharge) and prepare test documentation for utility approval</p></li><li><p>Liaise with SEWA/DEWA/TAQA for permits, inspections, and NOCs</p></li><li><p>Prepare method statements, RAMS, ITPs, as-built drawings, and cable schedules</p></li><li><p>Enforce PTW, LOTO, and HV safety procedures on site</p></li><li><p>Supervise technicians, jointers, and subcontractors; report daily progress to Project Manager</p></li><li><p>Conduct QA/QC checks at each installation stage</p></li></ul></div></section><section><p class="heading">Desired Candidate Profile</p><p class="paragraph"></p><ul><li><p>Bachelor's degree in Electrical Engineering or a related field, ensuring a strong theoretical foundation.</p></li><li><p>Minimum 3 years of hands-on experience in electrical site engineering, demonstrating practical expertise.</p></li><li><p>Professional certifications such as PMP or NEBOSH, showcasing commitment to project management and safety.</p></li><li><p>Experience in large-scale construction projects, preferably in commercial or industrial sectors.</p></li><li><p><strong>SEWA/DEWA/TAQA approved certification for HV works (preferred)</strong></p></li></ul><p></p></section>

<section><p class="heading jdMain">Job Description</p><p class="heading">Roles &amp; Responsibilities</p><div class="paragraph"><ul><li><p>Prepare electrical shop drawings: lighting layouts, small-power / power layouts, single-line diagrams, load / DB schedules, cable tray / trunking / containment routing, LV and electrical-room layouts, earthing and lightning protection, and risers.</p></li><li><p>Prepare wall-mounted device coordination (switches, sockets, manual call points, data, etc.) and reflected ceiling plans where required.</p></li><li><p>Produce material take-offs / BOQ.</p></li><li><p>Cross-check against approved submittals; reflect approved vendor and site data; prepare installation details and working clearances.</p></li><li><p>Coordinate electrical services with other trades and disciplines.</p></li></ul><ul><li><p>Verify cable sizing against load, derating and grouping factors.</p></li><li><p>Perform and verify voltage-drop checks within permitted limits.</p></li><li><p>Verify load-schedule balancing and diversity.</p></li><li><p>Check cable-tray fill, protective-device coordination and earthing arrangement.</p></li></ul></div></section><section><p class="heading">Desired Candidate Profile</p><p class="paragraph"></p><ul><li><p>3–6 years producing electrical MEP shop drawings on the contractor side; UAE / GCC experience preferred.</p></li><li><p>Diploma or Degree in Electrical Engineering or equivalent.</p></li></ul><ul><li><p>Proficient in AutoCAD and Revit MEP; Navisworks an advantage.</p></li><li><p>Familiarity with DEWA / local authority and BS / IEC requirements.</p></li></ul><p></p></section>

<section><p class="heading jdMain">Job Description</p><p class="heading">Roles &amp; Responsibilities</p><div class="paragraph"><ul><li><p><strong>Site Supervision:</strong> Lead and manage a team of electricians and helpers, ensuring tasks are completed efficiently and according to the project timeline.</p></li><li><p><strong>Installation &amp; Execution:</strong> Supervise and participate in cable installation, cable pulling, containment systems (conduits, trays, trunking), and final terminations.</p></li><li><p><strong>Power Distribution:</strong> Oversee the installation, dressing, and connection of <strong>LV Panels, MDBs, SMDBs, and DBs</strong>.</p></li><li><p><strong>Testing &amp; Commissioning:</strong> Conduct insulation resistance tests, continuity tests, and assist in the final commissioning of electrical systems.</p></li><li><p><strong>Troubleshooting:</strong> Identify and resolve electrical faults, wiring errors, and equipment malfunctions promptly.</p></li><li><p><strong>Compliance:</strong> Ensure all electrical works meet <strong>TAQA (Abu Dhabi Transmission &amp; Despatch Company)</strong> regulations and local authority standards.</p></li><li><p><strong>Material Management:</strong> Monitor material consumption on-site, verify deliveries, and ensure tools are maintained in good working condition.</p></li></ul></div></section><section><p class="heading">Desired Candidate Profile</p><p class="paragraph"></p><ul><li><p><strong>Experience:</strong> Minimum of <strong>4 years of experience</strong> within the <strong>UAE</strong> specifically in the construction sector.</p></li><li><p><strong>Technical Knowledge:</strong> Comprehensive understanding of Low Voltage (LV) systems, cable pulling, and termination techniques.</p></li><li><p><strong>Regulatory Knowledge:</strong> Deep familiarity with <strong>TAQA regulations</strong> and standard UAE electrical codes of practice.</p></li><li><p><strong>Skills:</strong> Ability to read and interpret electrical shop drawings, single-line diagrams (SLD), and load schedules.</p></li></ul><p><strong>Leadership:</strong> Proven ability to manage site teams and maintain discipline and productivity</p><br><p> <strong>Soft Skills:</strong></p><ul><li><p>Strong problem-solving abilities and attention to detail.</p></li><li><p>Strict adherence to Health, Safety, and Environment (<strong>HSE</strong>) protocols.</p></li><li><p><strong>Job Type: Full Time.</strong></p></li><li><p><strong>Joining: Immediately - 1-2 weeks.</strong></p></li></ul><br><p></p></section>

<p>• Develop detailed electrical design for high-voltage systems (11kV, 33kV, 132kV, and above) including single-line diagrams, cable schedules, control schematics, and layout drawings. • Perform load calculations, equipment sizing, cable sizing, and voltage drop analysis. • Prepare technical specifications and datasheets for HV equipment such as transformers, switchgears, circuit breakers, CTs, VTs, relays, and protection panels. • Design and review protection and control systems, including relay coordination and protection philosophy. • Interface with civil, mechanical, and instrumentation disciplines for interdisciplinary coordination. • Ensure compliance with IEC, IEEE, DEWA, SEC, or client-specific standards and codes. • Support in procurement activities by evaluating vendor offers, reviewing technical submissions, and performing FATs (Factory Acceptance Tests). • Prepare and review engineering documents, such as method statements, calculation notes, and test procedures. • Knowledge of simulation tools such as PVsyst, ETAP, and Dialux/ Equivalent software. • Familiar with International codes such as AS / NZS, IEC / EN, IEEE, BS, NFC and • Sizing/selection of PV module, SCB, Transformer, Inverter, HV/MV/LV switchgear/CRP Panel, Cable, Bus Bar/Duct, DG, UPS, Battery/Battery charger etc. • Participate in client and consultant meetings, and provide clarification on technical issues. </p><p>• Bachelor’s Degree in Electrical Engineering (Master’s is a plus). • Minimum 5–10 years of experience in HV electrical design within an EPC environment. • Strong knowledge of HV electrical systems, equipment, and industry practices. • Proficient in design tools such as ETAP, AutoCAD, DigSILENT, or similar software. • Familiarity with international codes and standards (IEC, IEEE, NEC, etc.). • Excellent written and verbal communication skills. • Ability to work in a fast-paced, team-oriented environment. </p>

1. About Solution Mall Solution Mall is a global B2B solution delivery platform serving power systems, electrical infrastructure, industrial facilities, commercial buildings, utilities, energy projects, communication networks, and project-based technical procurement needs. We support customers through requirement clarification, product matching, technical selection, supplier coordination, RFQ support, quotation coordination, delivery coordination, installation coordination, and long-term project follow-up. In the power system sector, Solution Mall supports products and solutions involving:Medium-voltage and low-voltage distribution networks MV/LV distribution substations Transformers and voltage stabilizers Switchgear and control cabinets Distribution panels and electrical cabinets Power cables and cable accessories Grounding and lightning protection systems Power protection and monitoring devices Electrical tools and testing instruments Project-based power system solution packages<br>2. Role Overview We are looking for a Power System Engineer – MV/LV Distribution Networks, UAE to support Solution Mall’s technical communication, product selection, RFQ follow-up, and project implementation support for power distribution projects in the UAE. This role is suitable for professionals with experience in power systems, electrical engineering, MV/LV distribution networks, transformers, voltage stabilizers, switchgear, electrical panels, distribution substations, industrial electrical systems, building electrical systems, or electrical project implementation. The main focus is to understand project requirements, support product and system selection, coordinate technical information, assist RFQ and quotation discussions, and support implementation for MV/LV distribution network and substation-related projects. This is a technical engineering and project-support role focused on MV/LV distribution systems, transformers, stabilizers, switchgear, distribution panels, site coordination, and project execution support.<br>3. Key Responsibilities Support technical communication with customers, electrical contractors, consultants, engineering firms, distributors, suppliers, and project stakeholders in the UAE. Clarify project requirements related to MV/LV distribution networks, distribution substations, transformers, voltage stabilizers, switchgear, electrical panels, power cables, grounding, and protection systems. Assist in product selection, technical comparison, specification review, RFQ preparation, quotation coordination, and technical confirmation. Support project implementation coordination, including equipment selection, site requirements, installation conditions, testing needs, delivery schedules, and handover support. Follow up on project drawings, equipment lists, load requirements, voltage levels, site environment, budget expectations, and delivery timelines. Coordinate with internal teams, suppliers, customers, contractors, and site teams to support project progress and issue resolution. Share market feedback on UAE electrical project requirements, preferred specifications, local standards, contractor habits, pricing levels, and project opportunities.<br>4. Qualifications Required2+ years of experience in one or more of the following areas:Power system engineering Electrical engineering MV/LV distribution networks MV/LV distribution substations Transformers or voltage stabilizers Switchgear or control cabinets Distribution panels or electrical cabinets Power cables and cable accessories Industrial or commercial electrical systems Electrical project implementation RFQ support or technical quotation coordination Ability to understand technical specifications, customer requirements, electrical application scenarios, product selection, RFQ follow-up, project documentation, and site implementation requirements. Good communication skills and ability to work with customers, contractors, consultants, suppliers, distributors, engineering teams, and project stakeholders. Working proficiency in English. Preferred Experience with UAE power system, electrical infrastructure, building electrical, industrial electrical, or utility-related projects Experience with MV/LV distribution equipment, transformers, voltage stabilizers, switchgear, electrical panels, grounding systems, or testing instruments Experience in site implementation, installation coordination, testing support, commissioning support, or project handover Familiarity with UAE electrical project workflows, local contractor resources, project approval processes, or site safety requirements Local electrician certificate, electrical license, or UAE-recognized electrical qualification is preferred Arabic communication ability is an advantage<br>5. Work Model This role focuses on technical support, project implementation support, and regional project opportunity development. The main focus areas include:Technical requirement clarification Product and system selection support MV/LV distribution network project support Distribution substation implementation support Transformer, stabilizer, and switchgear selection RFQ and quotation coordination Site coordination and technical communication Local market feedback Project advancement support This role is suitable for professionals with experience or access to electrical contractors, consultants, industrial facilities, building projects, utility-related projects, distributors, or power system project channels in the UAE.<br>6. Compensation and Benefits Solution Mall provides a results-oriented compensation model based on role scope, candidate experience, technical capability, project implementation support, customer development support, project progress, and business contribution. Details can be discussed during the interview process based on the candidate’s experience, technical background, UAE market resources, certification status, and project support capability.<br>7. How to Apply Please apply with a short note highlighting your experience in:Power system engineering MV/LV distribution networks MV/LV distribution substations Transformers or voltage stabilizers Switchgear or electrical panels Power cables and electrical accessories Electrical project implementation Site coordination or commissioning support UAE electrical project experience Local electrician certificate or electrical qualification, if available You may also send your updated CV to: xiaoting.xian@solutionmall.com with the email subject:Application: Power System Engineer – MV/LV Distribution Networks

<p>• Develop detailed electrical design for high-voltage systems (11kV, 33kV, 132kV, and above) including single-line diagrams, cable schedules, control schematics, and layout drawings. • Perform load calculations, equipment sizing, cable sizing, and voltage drop analysis. • Prepare technical specifications and datasheets for HV equipment such as transformers, switchgears, circuit breakers, CTs, VTs, relays, and protection panels. • Design and review protection and control systems, including relay coordination and protection philosophy. • Interface with civil, mechanical, and instrumentation disciplines for interdisciplinary coordination. • Ensure compliance with IEC, IEEE, DEWA, SEC, or client-specific standards and codes. • Support in procurement activities by evaluating vendor offers, reviewing technical submissions, and performing FATs (Factory Acceptance Tests). • Prepare and review engineering documents, such as method statements, calculation notes, and test procedures. • Knowledge of simulation tools such as PVsyst, ETAP, and Dialux/ Equivalent software. • Familiar with International codes such as AS / NZS, IEC / EN, IEEE, BS, NFC and • Sizing/selection of PV module, SCB, Transformer, Inverter, HV/MV/LV switchgear/CRP Panel, Cable, Bus Bar/Duct, DG, UPS, Battery/Battery charger etc. • Participate in client and consultant meetings, and provide clarification on technical issues. </p><p>• Bachelor’s Degree in Electrical Engineering (Master’s is a plus). • Minimum 5–10 years of experience in HV electrical design within an EPC environment. • Strong knowledge of HV electrical systems, equipment, and industry practices. • Proficient in design tools such as ETAP, AutoCAD, DigSILENT, or similar software. • Familiarity with international codes and standards (IEC, IEEE, NEC, etc.). • Excellent written and verbal communication skills. • Ability to work in a fast-paced, team-oriented environment. </p>

<h2 class="h5">Job description</h2> <div class="t-break" data-jb-field="description"> <p><strong>Petrofac is a leading international service provider to the energy industry, with a diverse client portfolio including many of the world’s leading energy companies.</strong></p><br><p>We design, build, manage and maintain infrastructure for our clients. We recruit, reward, and develop our people based on merit regardless of race, nationality, religion, gender, age, sexual orientation, marital status or disability. We value our people and treat everyone who works for or with Petrofac fairly and without discrimination.</p><br><p>The world is re-thinking its energy supply and energy security needs; planning for a phased transition to alternative energy sources. We are here to help our clients meet these evolving energy needs.</p><br><p>This is an exciting time to join us on this journey.</p><br><p>We support flexible working requests and have adopted a hybrid approach for most of our office-based roles. We ask employees to be present in the office at least three days per week.</p><br><p><i><strong>Are you ready to bring the right energy to Petrofac and help us deliver a better future for everyone?</strong></i></p><br><p><span><span><strong>JOB TITLE:&nbsp;Senior Engineer – Quality (EIT)</strong></span></span></p><br><p><span><span><strong>Location: Das Island site, &nbsp;Abu Dhabi</strong></span></span></p><br><p><span><span><strong>KEY RESPONSIBILITIES:</strong></span></span></p><br><p><span><span>·</span></span><span>Conduct cable glanding training, assess and approve cable glanding/termination personnel qualification.</span></p><br><p><span><span>·</span></span><span>Review and approve cable jointer/terminator qualification certificates.</span></p><br><p><span><span>·</span></span><span>Inspection/testing of temporary electrical works, connections to camp facilities as and when required.</span></p><br><p><span><span>·</span></span><span>Inspect installation of supports prior to cable tray installation.</span></p><br><p><span><span>·</span></span><span>Inspection of cable tray/conduit installation prior to release for cable laying.</span></p><br><p><span><span>·</span></span><span>Inspect UG stub ups.</span></p><br><p><span><span>·</span></span><span>Inspect cable trench for dimensions and sand bedding prior to cable laying and prior to release each layer of cables.</span></p><br><p><span><span>·</span></span><span>Monitor cable jointing/termination process to ensure manufacturer’s recommendations are followed.</span></p><br><p><span><span>·</span></span><span>Inspect cable segregation arrangement etc prior to back filling/release.</span></p><br><p><span><span>·</span></span><span>Inspect cable glanding ,termination, dressing etc.</span></p><br><p><span><span>·</span></span><span>Witness Insulation Resistance/continuity test of cables on the drum, after laying, prior to trench back filling and after termination.</span></p><br><p><span><span>·</span></span><span>Witness Hi-pot test of cables.</span></p><br><p><span><span>·</span></span><span>Inspect/witness final torquing of the cable termination.</span></p><br><p><span><span>·</span></span><span>Inspect installation of cable tray cover.</span></p><br><p><span><span>·</span></span><span>Surveillance during installation of equipment at substation to ensure manufacturer’s recommendations are followed.</span></p><br><p><span><span>·</span></span><span>Monitor preservation activities of switch gears, transformers, bus ducts and other equipment.</span></p><br><p><span><span>·</span></span><span>Inspection of switch gear installation for alignment, location etc.</span></p><br><p><span><span>·</span></span><span>Witness torquing of bus bar joints and doctor test.</span></p><br><p><span><span>·</span></span><span>Witness IR test of bus bar.</span></p><br><p><span><span>·</span></span><span>Witness Hi-pot test of bus bar wherever applicable.</span></p><br><p><span><span>·</span></span><span>Witness various testing of switchgears including IR, Hi-pot, ductor, operational etc.</span></p><br><p><span><span>·</span></span><span>Witness Transformer oil dielectric test.</span></p><br><p><span><span>·</span></span><span>Witness IR test of transformer.</span></p><br><p><span><span>·</span></span><span>Witness various electrical tests as per applicable ITP/vendor docs.</span></p><br><p><span><span>·</span></span><span>Final inspection of transformers, Switchgears, MCCs and other equipment’s.</span></p><br><p><span><span>·</span></span><span>Inspect installation of Bus duct.</span></p><br><p><span><span>·</span></span><span>Witness torquing, ductor/IR test of bus duct.</span></p><br><p><span><span>·</span></span><span>Inspect batteries, chargers and UPS. Where applicable, witness charging/discharging test of batteries.</span></p><br><p><span><span>·</span></span><span>Inspect underground earth cable installation, cad weld joints etc prior to trench back filling.</span></p><br><p><span><span>·</span></span><span>Inspect installation of earth electrode and earthing system.</span></p><br><p><span><span>·</span></span><span>Witness earth resistance test of individual electrodes and earthing network.</span></p><br><p><span><span>·</span></span><span>Witness earth loop resistance/continuity test.</span></p><br><p><span><span>·</span></span><span>Inspection of lightning protection system of each building.</span></p><br><p><span><span>·</span></span><span>Final inspection of earthing system.</span></p><br><p><span><span>·</span></span><span>Inspect location of each lighting fixtures, socket out lets, junction boxes with respect to type/application.</span></p><br><p><span><span>·</span></span><span>Inspect site routed lighting cable tray installation and release for cable laying.</span></p><br><p><span><span>·</span></span><span>Inspect installation of distribution boards.</span></p><br><p><span><span>·</span></span><span>Witness IR test of distribution boards.</span></p><br><p><span><span>·</span></span><span>Witness IR/continuity test of lighting circuits.</span></p><br><p><span><span>·</span></span><span>Witness functional test of each lighting circuits, where applicable only.</span></p><br><p><span><span>·</span></span><span>Witness illumination level test, where applicable only.</span></p><br><p><span><span>·</span></span><span>Monitor preservation activities of motors throughout project period.</span></p><br><p><span><span>·</span></span><span>Inspect installation of motors including glanding termination, earthing.</span></p><br><p><span><span>·</span></span><span>Witness IR test and /or polarization index test etc as applicable.</span></p><br><p><span><span>·</span></span><span>Inspect installation of local control stations.</span></p><br><p><span><span>·</span></span><span>Witness functional test from local control station to Substation, if applicable.</span></p><br><p><span><span>·</span></span><span>Witness motor solo run test (2hrs for LV motors and 4 hrs for MV/HV motors), if applicable.</span></p><br><p><span><span>·</span></span><span>Inspect thermite welding on top of UG pipe and witness continuity test of cables.</span></p><br><p><span><span>·</span></span><span>Inspect installation of temporary magnesium anode, reference electrode, anode ribbon, crossings.</span></p><br><p><span><span>·</span></span><span>Witness various inspection/testing related to CP system prior to backfillin</span></p> </div>

<h2 class="h5">Job description</h2> <div class="t-break" data-jb-field="description"> <span> <b><span>1. Technical Expertise &amp; Support</span></b> </span><ul> <li><p><span>Deliver detailed </span><b><span>product demonstrations</span></b><span>, </span><b><span>presentations</span></b><span>, and </span><b><span>training sessions</span></b><span> on cable fault location, Very Low Frequency (VLF) testing, and Partial Discharge (PD) diagnostic systems.</span></p><br></li> <li><p><span>Provide </span><b><span>pre- and post-sales technical support</span></b><span> to customers, distributors, and internal teams.</span></p><br></li> <li><p><span>Assist customers in </span><b><span>interpreting test results</span></b><span> and offer diagnostic insights or recommended actions for cable condition assessment.</span></p><br></li> <li><p><span>Support the </span><b><span>commissioning, setup, and calibration</span></b><span> of MV/HV testing and PD measurement equipment.</span></p><br></li> <li><p><span>Prepare </span><b><span>technical documentation</span></b><span>, user guides, and training materials to enhance client understanding and equipment utilization.</span></p><br></li> <li><p><span>Liaise with the engineering and R&amp;D teams to provide </span><b><span>feedback on product performance</span></b><span>, feature enhancements, and market requirements.</span></p><br></li> </ul><b><span>2. Customer Engagement &amp; Business Support</span></b> <ul> <li><p><span>Collaborate with the </span><b><span>sales and business development teams</span></b><span> to identify client needs and propose technically sound solutions.</span></p><br></li> <li><p><span>Participate in </span><b><span>on-site customer visits</span></b><span>, </span><b><span>technical seminars</span></b><span>, </span><b><span>workshops</span></b><span>, and </span><b><span>webinars</span></b><span> to promote awareness of diagnostic testing methodologies.</span></p><br></li> <li><p><span>Serve as a </span><b><span>subject matter expert (SME)</span></b><span> at trade shows, exhibitions, and industry events.</span></p><br></li> <li><p><span>Support </span><b><span>key account management</span></b><span> by providing application-based insights and strengthening customer relationships.</span></p><br></li> <li><p><span>Assist in the preparation of </span><b><span>technical proposals</span></b><span>, tenders, and specifications in coordination with sales and product teams.</span></p><br></li> </ul><b><span>3. Quality &amp; Compliance</span></b> <ul> <li><p><span>Ensure that all technical activities are conducted in compliance with </span><b><span>company procedures, industry standards, and safety regulations</span></b><span>.</span></p><br></li> <li><p><span>Maintain accurate records of demonstrations, site visits, and customer communications for reporting and analysis.</span></p><br></li> <li><p><span>Stay updated on </span><b><span>emerging technologies, IEC/IEEE standards</span></b><span>, and diagnostic methodologies relevant to high-voltage cable testing.</span></p><br></li> </ul> <br><span>Requirements </span><ul> <li><p><b><span>Bachelor’s Degree</span></b><span> in Electrical Engineering or related discipline (Master’s degree preferred).</span></p><br></li> <li><p><b><span>Minimum 3 years of experience</span></b><span> in cable testing, insulation diagnostics, or partial discharge analysis.</span></p><br></li> <li><p><span>In-depth understanding of </span><b><span>MV/HV cable systems</span></b><span>, insulation degradation mechanisms, and PD phenomena.</span></p><br></li> <li><p><span>Experience in field testing, troubleshooting, and diagnostics of underground cable networks.</span></p><br></li> <li><p><span>Familiarity with </span><b><span>VLF testing, TDR, and PD testing</span></b><span> methods and standards (e.g., IEC 60270).</span></p><br></li> <li><p><b><span>Knowledge of Megger</span></b><span> or equivalent testing equipment is an advantage.</span><br></p><br></li> </ul> <br> </div>

<p>The key duties and responsibilities of the Electrical Design Engineer include, but are not limited to:</p><ul><li><p>Design & Documentation: Prepare detailed layouts, containment routing, schematic diagrams, and Single Line Diagrams (SLDs) for internal/external lighting, small power, low voltage (LV) distribution, lightning protection, and earthing systems.</p></li></ul><ul><li><p>Engineering Calculations: Conduct accurate electrical load estimations, maximum demand calculations, cable sizing, short-circuit analyses, and voltage drop calculations.</p></li></ul><ul><li><p>Lighting Simulation: Create point-by-point indoor, outdoor, and emergency lighting simulations using DIALux/DIALux evo to verify lux level compliance, uniformity, and energy efficiency targets.</p></li></ul><ul><li><p>ELV Systems Coordination: Assist in or directly handle the basic design and integration of Extra-Low Voltage systems, including fire alarm, CCTV, access control, ICT structured cabling, and Central Emergency Battery systems.</p></li></ul><ul><li><p>Interdisciplinary Coordination: Actively participate in Building Information Modeling (BIM) coordination reviews to detect, track, and resolve spatial clashes with HVAC, plumbing, structural, and architectural elements.</p></li></ul><ul><li><p>Authority Approvals: Prepare technical submission packages, load schedules, and drawings for compliance reviews and approval by municipal bodies and local utilities.</p></li></ul><p><strong>Desired Candidate Profile</strong></p><ul><li><p>Education: Bachelor’s Degree in Electrical Engineering from an accredited university.</p></li><li><p>Experience: 2 to 5 years of proven design office experience specifically within building services consultancy, architectural firms, or the technical design department of a main contractor.</p></li></ul><ul><li><p>BIM & CAD Software Proficiency: Strong working knowledge of Autodesk Revit (MEP) for 3D modeling and extraction, alongside advanced proficiency in AutoCAD.</p></li></ul><ul><li><p>Technical Software: High proficiency in DIALux/DIALux evo, and familiarity with electrical analysis tools (such as ETAP, Amtech/Trimble, or advanced MS Excel calculation models).</p></li></ul><ul><li><p>Codes & Standards: Solid foundational knowledge of regional utility regulations (e.g., SEWA/DEWA/ADDC regulations) and international standards like BS 7671 or IEC.</p></li></ul><ul><li><p>Professional Credentials: Eligibility for or active membership in the local Society of Engineers (or equivalent municipal engineering registration) is highly advantageous.</p></li></ul><ul><li><p>Core Competencies: Strong analytical problem-solving skills, proactive approach to multi-disciplinary coordination, and clear technical communication skills.</p></li></ul>

Petrofac is a leading international service provider to the energy industry, with a diverse client portfolio including many of the world’s leading energy companies.<br><br>We design, build, manage and maintain infrastructure for our clients. We recruit, reward, and develop our people based on merit regardless of race, nationality, religion, gender, age, sexual orientation, marital status or disability. We value our people and treat everyone who works for or with Petrofac fairly and without discrimination.<br><br>The world is re-thinking its energy supply and energy security needs; planning for a phased transition to alternative energy sources. We are here to help our clients meet these evolving energy needs.<br><br>This is an exciting time to join us on this journey.<br><br>We support flexible working requests and have adopted a hybrid approach for most of our office-based roles. We ask employees to be present in the office at least three days per week.<br><br>Are you ready to bring the right energy to Petrofac and help us deliver a better future for everyone?<br><br>JOB TITLE: Senior Engineer – Quality (EIT)<br><br>Location: Das Island site, Abu Dhabi<br><br>Key Responsibilities<br><br> Conduct cable glanding training, assess and approve cable glanding/termination personnel qualification. Review and approve cable jointer/terminator qualification certificates. Inspection/testing of temporary electrical works, connections to camp facilities as and when required. Inspect installation of supports prior to cable tray installation. Inspection of cable tray/conduit installation prior to release for cable laying. Inspect UG stub ups. Inspect cable trench for dimensions and sand bedding prior to cable laying and prior to release each layer of cables. Monitor cable jointing/termination process to ensure manufacturer’s recommendations are followed. Inspect cable segregation arrangement etc prior to back filling/release. Inspect cable glanding ,termination, dressing etc. Witness Insulation Resistance/continuity test of cables on the drum, after laying, prior to trench back filling and after termination. Witness Hi-pot test of cables. Inspect/witness final torquing of the cable termination. Inspect installation of cable tray cover. Surveillance during installation of equipment at substation to ensure manufacturer’s recommendations are followed. Monitor preservation activities of switch gears, transformers, bus ducts and other equipment. Inspection of switch gear installation for alignment, location etc. Witness torquing of bus bar joints and doctor test. Witness IR test of bus bar. Witness Hi-pot test of bus bar wherever applicable. Witness various testing of switchgears including IR, Hi-pot, ductor, operational etc. Witness Transformer oil dielectric test. Witness IR test of transformer. Witness various electrical tests as per applicable ITP/vendor docs. Final inspection of transformers, Switchgears, MCCs and other equipment’s. Inspect installation of Bus duct. Witness torquing, ductor/IR test of bus duct. Inspect batteries, chargers and UPS. Where applicable, witness charging/discharging test of batteries. Inspect underground earth cable installation, cad weld joints etc prior to trench back filling. Inspect installation of earth electrode and earthing system. Witness earth resistance test of individual electrodes and earthing network. Witness earth loop resistance/continuity test. Inspection of lightning protection system of each building. Final inspection of earthing system. Inspect location of each lighting fixtures, socket out lets, junction boxes with respect to type/application. Inspect site routed lighting cable tray installation and release for cable laying. Inspect installation of distribution boards. Witness IR test of distribution boards. Witness IR/continuity test of lighting circuits. Witness functional test of each lighting circuits, where applicable only. Witness illumination level test, where applicable only. Monitor preservation activities of motors throughout project period. Inspect installation of motors including glanding termination, earthing. Witness IR test and /or polarization index test etc as applicable. Inspect installation of local control stations. Witness functional test from local control station to Substation, if applicable. Witness motor solo run test (2hrs for LV motors and 4 hrs for MV/HV motors), if applicable. Inspect thermite welding on top of UG pipe and witness continuity test of cables. Inspect installation of temporary magnesium anode, reference electrode, anode ribbon, crossings. Witness various inspection/testing related to CP system prior to backfilling and after back filling. Inspect installation of CP transformer/rectifier. Inspect installation of heat tracing circuits and associated components. Witness testing of heat tracing circuits prior to insulation and after cladding. Witness inspection and tests related to equipment such as diesel generators, HVAC equipment etc. Witness inspection/testing related to overhead power distribution/transmission lines. Perform initial detailed inspection of certified electrical equipment based on latest IEC 60079-17 table 1,2,3 and IEC 60079-14, or perform visual or close inspection as applicable. Correct interpretation of equipment labels, IP Rating etc. Verify IP Rating is maintained. Conduct tubing/tube fitting installation training, assess and approve instrument tube fitter personnel qualification. Inspect each instrument against data sheet prior to release to site for installation. Witness calibration of each instrument as required by ITP/specifications. Witness calibration of safety valves. Witness calibration and seat leakage test of control valves. Monitor preservation requirements of instruments and control panels. Inspect instrument stanchions, location, mounting height, orientation etc. Inspect installation of Instruments including glanding termination of cables. Inspect installation/hook up and pressure test of impulse tubing. Witness pressure test of impulse tubes. Inspect installation of air supply/signal lines. Witness pressure/leak testing of air supply/signal lines. Witness inspection/test related to analyser houses. Verify completion of heat tracing for impulse tubes. Inspect installation of supports prior to cable tray installation. Inspection of cable tray/conduit installation prior to release for cable laying. Inspect UG stub-ups Inspect cable trench for sand bedding prior to cable laying and release each layer. Witness IR/continuity test of cables on the drum, prior to back filling trench, after glanding and termination. Inspect cable segregation arrangement etc prior to back filling. Inspect cable glanding, termination, dressing etc. Inspect installation of cable tray cover if reqd. Inspect control room building prior to installation of panels. Surveillance during installation of equipment at control room to ensure manufacturer’s recommendations are followed. Inspect installation of various control panels, consoles, desks etc. Inspect internal cable tray works prior to installation of cables. Inspect installation of various cables including system cables. Witness testing of all cables. Monitor preservation requirements of communication equipment and control panels. Conduct cable glanding training, assess and approve cable glanding/termination personnel qualification. Review and approve F. O cable technician’s qualification certificates. Inspect equipment stanchions, location, mounting height, orientation etc. Inspect installation of communication equipment including glanding termination of cables. Inspect installation of supports prior to cable tray installation. Inspection of cable tray/conduit installation prior to release for cable laying. Inspect UG stub-ups. Inspect cable trench for sand bedding prior to cable laying and release each layer. Witness IR/continuity test of telecom copper cables on the drum, prior to back filling trench, after glanding and termination. Inspect cable segregation arrangement etc prior to back filling. Inspect cable glanding, termination, dressing etc. Witness testing of fiber optic cables testing prior to installation, prior to trench back filling and final test. Witness communication cable testing Witness testing of communication system Inspect installation of cable tray cover if reqd. Inspect control room building prior to installation of panels. Surveillance during installation of equipment at control room to ensure manufacturer’s recommendations are followed. Inspect installation of various control panels, consoles, desks etc. Inspect internal cable tray works prior to installation of cables. Inspect installation of various cables including system cables. Witness testing of all cables. Inspect termination of cables in each panel. Inspect instrument earthing of panels, cables etc. Monitor pest control activities inside control building. Inspection and testing of the PA/GA circuits, CCTV components, telephone units, exchange, and other systems as applicable. Inspect location, mounting height of JB’s Local panels against drawings. Inspect wiring inside each JB’s and local panels. Witness testing of control panels. Inspect installation of various types of antennas and radio tower/mast. Perform initial detailed inspection of certified electrical equipment based on latest IEC 60079-17 table 1,2,3 and IEC 60079-14, or perform visual or close inspection as applicable. Correct interpretation of equipment labels, IP Rating etc. Verify IP Rating is maintained.<br><br>Essential Qualifications And Skills<br><br> Diploma in Electrical Engineering or equivalent Minimum 10 years’ experience as Electrical QC Inspector. Should have experience in oil & gas/Petrochemical industry. Should have previously worked with major EPC contractors (At least three years). For Hazardous Area Electrical Inspections: Should be an experienced person whose training has included instructions on various types of protection and installation practices, IEC 60079-17 and IEC 60079-14. (Evidence of relevant experience and training claimed shall be documented and available). If no such training attended, he should undergo in-house training: PEC-RCD-00384, prior to assigning any Ex-Inspections.<br><br>Additional Information

<ol><li><p>Manage the laying, glancing, and termination of LV and HV cables, ensuring compliance with industry standards and electrical safety regulations.</p></li><li><p>Oversee the installation of electrical panels, distribution boards, and other critical electrical infrastructure, ensuring seamless integration and optimal functionality.</p></li><li><p>Coordinate with site supervisors and labor teams to execute electrical installation projects, providing clear guidance and support to ensure project objectives are achieved.</p></li><li><p>Develop and implement detailed project plans, including resource allocation, timelines, and material procurement strategies to meet project deadlines.</p></li><li><p>Conduct regular site inspections to monitor electrical installation progress, identify potential risks, and provide solutions to address any electrical safety concerns.</p></li></ol><p><strong>Desired Candidate Profile</strong></p><ol><li><p>B E / B Tech in Electrical and Electronics Engineering (EEE) or Electrical Engineering with a minimum of 5 years of relevant experience, or a Diploma in Electrical Engineering with 10+ years of experience in electrical installations.</p></li><li><p>Substantial experience (5-10 years) in low voltage and high voltage cable installations, with a focus on LVHV cable laying, glancing, and termination.</p></li><li><p>Demonstrated expertise in installing electrical panels and distribution boards, ensuring optimal performance and safety.</p></li><li><p>Proven ability to manage a large-scale workforce, comprising a minimum of 4 supervisors and 100 workmen, ensuring efficient project execution and team coordination.</p></li><li><p>Excellent communication and leadership skills, with the ability to interact effectively with diverse teams, suppliers, and stakeholders to achieve project objectives<br><br></p><p><strong>Eligibility Criteria</strong></p><p>✔ Experience in construction (not design), Pipeline / Oil & Gas / EPC / Flowline / Wellhead / Brownfield / Upstream / Onshore</p><p>✔ Gulf / ADNOC experience preferred</p><p>✔ Clean-shaven policy applicable</p><p>✔ Candidates must be immediate joiners</p><p>❌ Candidates with Metro / Building / Road Infrastructure experience are not eligible</p><p>Attached JDs for your reference.<br></p><p><strong>Age Criteria:</strong></p><p>Maximum age limit is 49 years</p><p>For managerial positions, this may be extended up to 50 years if the candidate has significant Gulf experience<br></p><p><strong>Managerial and SR. Positions:</strong></p><p>A minimum of 5 years of Gulf experience in the relevant field is mandatory<br></p><p><strong>Interview Date:</strong> Mumbai - 09th Aug 2026, Sunday, Chennai - 12th Aug 2026, Wednesday & Kochi - 16th Aug 2026, Sunday - Reporting time – 08:30 AM to 12:00 PM & 2:30 PM to 3:30 PM<br></p><p><strong>Mumbai - Mirage Hotel,</strong></p><p>Mumbai International Airport Approach Road, Near Marol Aqua Metro Stn. Andheri (East), Mumbai, Maharashtra, India – 400 059.</p><p>Waiting Hall – Amber Hall<br></p><p><strong>Chennai - The Residency Towers,</strong></p><p>115, Sir Thyagaraya Road, Chennai 600017</p><p>Waiting Hall – Senator Hall<br></p><p><strong>Kochin - Crowne Plaza Kochi,</strong></p><p>XI 641A Kundanoor Junction, NH-47 Bypass</p><p>Maradu, Ernakulam, Kerala, India, 682305</p><p>Waiting Hall – Onam Hall</p></li></ol>

<section><p class="heading jdMain">Job Description</p><p class="heading">Roles &amp; Responsibilities</p><div class="paragraph"><ul><li><p><strong>Design and review electrical systems for MEP projects</strong> including power distribution, lighting, ELV, and earthing systems.</p></li><li><p><strong>Prepare electrical load calculations</strong>, voltage drop calculations, and cable sizing.</p></li><li><p>Develop and review <strong>shop drawings, layouts, and as-built drawings</strong>.</p></li><li><p><strong>Prepare detailed electrical drawings</strong> including, Power distribution layouts, Cable routing and tray layouts, Earthing and lightning protection drawings, Single Line Diagrams (SLD), Panel board layouts and schematics.</p></li><li><p><strong>Develop and modify 2D and 3D models using</strong> <strong>AutoCAD and BIM platforms</strong>.</p></li><li><p><strong>Perform clash detection and coordination using Navisworks</strong>.</p></li><li><p>Coordinate with mechanical, plumbing, and civil teams to ensure integrated project delivery.</p></li><li><p>Supervise on-site electrical installations and ensure compliance with approved drawings and specifications.</p></li><li><p>Conduct site inspections, testing, and commissioning of electrical systems.</p></li><li><p>Ensure compliance with local authority regulations (e.g., DEWA, ADDC) and international standards.</p></li><li><p>Review material submittals, technical datasheets, and method statements.</p></li><li><p>Support project planning, scheduling, and progress monitoring.</p></li><li><p>Attend client meetings, technical discussions, and coordination meetings.</p></li></ul></div></section><section><p class="heading">Desired Candidate Profile</p><p class="paragraph"></p><ul><li><p>Strong knowledge of:</p><ul><li><p>Power Distribution Systems (LV/MV)</p></li><li><p>Lighting Design and Controls</p></li><li><p>ELV Systems (Fire Alarm, CCTV, Data, Access Control)</p></li><li><p>Earthing and Lightning Protection Systems</p></li></ul></li><li><p>Proficiency in:</p><ul><li><p>AutoCAD (mandatory)</p></li><li><p>Revit MEP (preferred)</p></li><li><p>MS Office tools</p></li></ul></li><li><p>Ability to interpret:</p><ul><li><p>Single Line Diagrams (SLD)</p></li><li><p>Electrical Schematics and Layout Drawings</p></li></ul></li><li><p>Familiarity with international standards such as IEC, BS, and local authority regulations (DEWA/SEWA/ADDC).</p></li></ul><p></p></section>

<h2 class="h5">Job description</h2> <div class="t-break" data-jb-field="description"> <p><b>Title:</b></p><br><br>Specialist Electrical Engineer – Offshore Water Injection Project<br><br><p><b><i>Belong, Connect, Grow, with KBR!</i></b></p><br><br><p><b><i>The KBR team of teams delivers future-forward science, technology and engineering solutions and mission-critical services that help governments and companies around the world accomplish their most important objectives, while also helping achieve their sustainability goals. KBR Sustainable Technology Solutions provides holistic and value-added solutions across the entire asset life cycle. These include world-class licensed process technologies, differentiated advisory services, deep technical domain expertise, energy transition solutions, high-end design and engineering capabilities, and smart solutions to optimize planned and operating assets.</i></b></p><br><br><p><b><u>&nbsp;<span>Job Title: Specialist</span><span> Electrical Engineer</span> </u></b><b><u><span>– Offshore Water Injection Project</span></u></b></p><br><br><p>KBR Abu Dhabi PMC Team is currently looking to fill a position of <b><u>Specialist Electrical Engineer </u></b>for an <b>Offshore Project </b>to be based in UAE ( Abu Dhabi) as soon as the administrative processes are completed, will then relocate to <b>Spain Office</b> and then return to Abu Dhabi<b>&nbsp;. </b></p><br><br><p><b>Job Purpose</b></p><br><br><p><b>The Specialist Electrical Engineer is responsible for the design, engineering, review, and technical support of electrical systems for an Offshore Water Injection Project. The role ensures all electrical equipment and installations comply with project specifications, international standards, client requirements, and applicable safety regulations while supporting project execution from concept through commissioning and start-up.</b></p><br><br><p><b>Key Responsibilities</b></p><br><br><p><b>Electrical Engineering &amp; Design</b></p><br><br><ul><li><b>Develop and review electrical design deliverables for offshore water injection facilities.</b></li><li><b>Perform electrical system studies including load flow, short circuit, motor starting, harmonic analysis, and protection coordination studies.</b></li><li><b>Prepare and review electrical equipment specifications, datasheets, calculations, and requisitions.</b></li><li><b>Ensure compliance with project requirements, IEC, IEEE, NFPA, API, and client standards.</b></li></ul><p><b>Power Generation &amp; Distribution</b></p><br><br><ul><li><b>Design and review medium-voltage (MV) and low-voltage (LV) power distribution systems.</b></li><li><b>Support electrical integration of water injection pumps, seawater lift pumps, and other rotating equipment.</b></li><li><b>Review single-line diagrams (SLDs), load lists, cable schedules, and power distribution philosophies.</b></li><li><b>Ensure reliability and availability of critical offshore electrical systems.</b></li></ul><p><b>Equipment Engineering</b></p><br><br><ul><li><b>Provide technical expertise for procurement and evaluation of: </b><ul><li><b>Generators</b></li><li><b>Transformers</b></li><li><b>Switchgear (MV/LV)</b></li><li><b>Variable Frequency Drives (VFDs)</b></li><li><b>Motors</b></li><li><b>UPS Systems</b></li><li><b>Battery Chargers</b></li><li><b>Lighting Systems</b></li><li><b>Cathodic Protection Systems</b></li><li><b>Electrical Heat Tracing</b></li></ul></li><li><b>Participate in vendor evaluations, technical bid analysis, and supplier meetings.</b></li></ul><p><b>Hazardous Area Compliance</b></p><br><br><ul><li><b>Ensure electrical equipment complies with hazardous area classification requirements.</b></li><li><b>Review and verify Ex equipment selection and installation.</b></li><li><b>Support hazardous area studies and HAZOP/HAZID reviews.</b></li><li><b>Ensure compliance with IECEx, ATEX, and project-specific offshore requirements.</b></li></ul><p><b>Construction &amp; Commissioning Support</b></p><br><br><ul><li><b>Provide engineering support during fabrication, installation, pre-commissioning, and commissioning.</b></li><li><b>Review vendor documents and resolve technical queries.</b></li><li><b>Support site troubleshooting and commissioning activities.</b></li><li><b>Participate in FAT, SAT, and system acceptance testing.</b></li></ul><p><b>Interface Management</b></p><br><br><ul><li><b>Coordinate with Mechanical, Instrumentation, Process, Civil, and Project teams.</b></li><li><b>Support client meetings, design reviews, and technical workshops.</b></li><li><b>Manage interfaces with EPC contractors, vendors, and third-party consultants.</b></li></ul><br><p><b>Key Systems &amp; Equipment Experience</b></p><br><br><p><b>Experience with one or more of the following is highly desirable:</b></p><br><br><p><b>Electrical Systems</b></p><br><br><ul><li><b>Offshore Power Generation Systems</b></li><li><b>MV/LV Distribution Networks</b></li><li><b>Emergency Power Systems</b></li><li><b>Diesel Generators</b></li><li><b>UPS and Battery Systems</b></li><li><b>Cathodic Protection Systems</b></li><li><b>Lighting and Small Power Systems</b></li></ul><p><b>Rotating Equipment</b></p><br><br><ul><li><b>Water Injection Pumps</b></li><li><b>Seawater Lift Pumps</b></li><li><b>Booster Pumps</b></li><li><b>Variable Speed Drive Applications</b></li></ul><p><b>Control &amp; Protection</b></p><br><br><ul><li><b>Electrical Protection Systems</b></li><li><b>Motor Control Centers (MCCs)</b></li><li><b>SCADA Interface Systems</b></li><li><b>Power Management Systems (PMS)</b></li><li><b>Emergency Shutdown Systems (ESD)</b></li></ul><br><p><b>Qualifications</b></p><br><br><ul><li><b>Bachelor’s Degree in Electrical Engineering.</b></li><li><b>Master’s Degree is an advantage.</b></li><li><b>Professional Engineering certification is preferred.</b></li></ul><br><p><b>Experience</b></p><br><br><ul><li><b>15+ years of electrical engineering experience within Oil &amp; Gas, Offshore, EPC, or Energy projects.</b></li><li><b>Minimum 5 years in a Specialist or Senior Electrical Engineering role.</b></li><li><b>Proven experience on offshore platforms, water injection projects, FPSOs, offshore processing facilities, or subsea developments.</b></li><li><b>Strong experience with FEED, Detailed Engineering, EPC, and commissioning phases.</b></li></ul><br><p><b>Technical Competencies</b></p><br><br><ul><li><b>Electrical System Design</b></li><li><b>Power System Studies</b></li><li><b>Load Flow Analysis</b></li><li><b>Short Circuit Analysis</b></li><li><b>Protection Coordination Studies</b></li><li><b>Electrical Equipment Specification</b></li><li><b>Hazardous Area Engineering</b></li><li><b>Electrical Safety Compliance</b></li><li><b>Vendor Package Engineering</b></li><li><b>Commissioning &amp; Start-Up Support</b></li><li><b>ETAP, SKM, DIgSILENT PowerFactory</b></li><li><b>IEC, IEEE, API, NFPA Standards</b></li></ul><br><br><br><br> </div>