وظائف مهندس ميكانيكا معدات ثقيلة

<h2 class="h5">Job description</h2> <div class="t-break" data-jb-field="description"> Company Description<br><p>With a legacy of over 40 years, GCG Engineering Services excels in delivering cutting-edge solutions and aftermarket support for precision instruments, metering systems, flow controls, heat exchangers, automation, plus electrical &amp; instrumentation bulk trading. Renowned for its reliability and expertise, GCG Engineering Services supports the Oil &amp; Gas, Water, Power, and Industrial sectors, enhancing operational efficiency and delivering unmatched value across the GCC region.</p><br><br>Job Description<br><ul><li>Supervise and coordinate HVAC installation, maintenance, repair, testing, and commissioning activities.</li><li>Lead and monitor HVAC technicians, mechanics, ducting technicians, pipe fitters, helpers, and subcontractor personnel.</li><li>Review approved IFC drawings, shop drawings, technical specifications, method statements, and work schedules before commencing activities.</li><li>Plan and allocate manpower, materials, tools, equipment, and resources to ensure timely completion of assigned work.</li><li>Ensure proper installation, alignment, insulation, supports, vibration isolators, dampers, grilles, diffusers, and other HVAC accessories.</li><li>Monitor daily work progress and ensure activities are completed in accordance with approved schedules and project requirements.</li><li>Coordinate with mechanical engineers, electrical supervisors, civil teams, instrumentation personnel, vendors, subcontractors, and other disciplines to avoid work conflicts and delays.</li><li>Conduct routine site inspections to verify workmanship, installation quality, and compliance with approved drawings and specifications.</li><li>Ensure all work is performed in accordance with approved Method Statements, Inspection and Test Plans (ITPs), Quality Control Procedures, and project requirements.</li><li>Identify technical issues, material shortages, design conflicts, and site constraints and report them to the responsible engineer or project management team.</li><li>Coordinate HVAC testing and commissioning activities, including pressure testing, flushing, cleaning, air balancing, water balancing, functional testing, and performance verification.</li><li>Verify that HVAC systems are properly tested and operational before handover.</li><li>Ensure inspection requests, checklists, test reports, and relevant quality documentation are completed and submitted as required.</li><li>Maintain daily manpower reports, work progress reports, equipment utilization records, and site activity reports.</li><li>Monitor material usage and minimize wastage, rework, and unnecessary consumption.</li><li>Ensure proper housekeeping and safe storage of materials, tools, and equipment at the worksite.</li><li>Conduct toolbox talks and ensure that all personnel understand job hazards, control measures, and safe work procedures.</li><li>Enforce compliance with company and client Health, Safety, and Environment (HSE) requirements.</li><li>Ensure that required permits, risk assessments, Job Safety Analyses (JSAs), and work authorizations are available before starting work.</li><li>Stop unsafe work and immediately report unsafe conditions, incidents, near misses, and hazards.</li><li>Participate in project meetings, progress reviews, safety meetings, inspections, and coordination meetings.</li><li>Support pre-commissioning, commissioning, system handover, punch-list clearance, and final project closeout activities.</li><li>Ensure proper maintenance records and equipment history are maintained for operational and maintenance projects.</li><li>Assist in troubleshooting HVAC system failures and coordinate corrective and preventive maintenance activities.</li><li>Perform other duties assigned by the Mechanical Engineer, Project Manager, or Maintenance Manager.</li></ul><br>Qualifications<br><ul><li>Minimum 7–10&nbsp;years of experience in&nbsp;HVAC installation, construction, maintenance, testing, commissioning, or operations.</li><li>Minimum 3–5 years of experience in a supervisory role.</li><li>Experience in oil &amp; gas, industrial, petrochemical, power, commercial, or large-scale construction projects is preferred.</li><li>Experience working under major client specifications and international standards is an advantage.</li></ul><br>Additional Information<br><ul><li>Strong willingness to learn and adapt to a dynamic project environment.</li><li>Attention to detail with a commitment to quality and safety.</li><li>Effective communication skills and a team-oriented approach.</li><li>Ability to follow instructions, meet deadlines, and manage time effectively.</li><li>Willingness to work on-site at various ADNOC project locations in Abu Dhabi.</li><li>Flexibility to work in shifts and extended hours as project demands require.</li></ul><br><br> </div>

<p>A reputable company in Dubai is looking for an experienced and responsible Heavy Vehicle Driver to handle the safe transportation of goods, materials, and equipment. The ideal candidate should have strong knowledge of UAE roads and safe driving practices.</p> <p>Key Responsibilities<br /> Operate heavy vehicles safely and responsibly.<br /> Transport goods, materials, and equipment to designated locations.<br /> Follow assigned routes and delivery schedules.<br /> Inspect the vehicle before and after each trip.<br /> Ensure cargo is properly loaded, secured, and delivered safely.<br /> Maintain accurate delivery notes and transportation records.<br /> Report vehicle defects, accidents, delays, or other issues to management.<br /> Follow UAE traffic laws and company transportation procedures.<br /> Coordinate with warehouse, logistics, and site teams when required.<br /> Maintain the vehicle in clean and safe operating condition.<br /> Complete routine checks and report maintenance requirements.<br /> Ensure timely delivery while maintaining safety standards.<br /> Requirements<br /> Valid UAE Heavy Vehicle Driving License.<br /> Minimum 2–3 years of heavy vehicle driving experience.<br /> Good knowledge of UAE roads and major locations.<br /> Clean driving record with strong road-safety awareness.<br /> Ability to handle loading and unloading procedures when required.<br /> Responsible, punctual, and physically fit.<br /> Good communication skills.<br /> UAE experience is preferred.</p> <p>Interested candidates may submit their updated CV to: info.aljamal.travelandtourism@gmail.com</p>

<p>A reputable company in Dubai is looking for an experienced and responsible Heavy Vehicle Driver to handle the safe transportation of goods, materials, and equipment. The ideal candidate should have strong knowledge of UAE roads and safe driving practices.</p> <p>Key Responsibilities<br /> Operate heavy vehicles safely and responsibly.<br /> Transport goods, materials, and equipment to designated locations.<br /> Follow assigned routes and delivery schedules.<br /> Inspect the vehicle before and after each trip.<br /> Ensure cargo is properly loaded, secured, and delivered safely.<br /> Maintain accurate delivery notes and transportation records.<br /> Report vehicle defects, accidents, delays, or other issues to management.<br /> Follow UAE traffic laws and company transportation procedures.<br /> Coordinate with warehouse, logistics, and site teams when required.<br /> Maintain the vehicle in clean and safe operating condition.<br /> Complete routine checks and report maintenance requirements.<br /> Ensure timely delivery while maintaining safety standards.<br /> Requirements<br /> Valid UAE Heavy Vehicle Driving License.<br /> Minimum 2–3 years of heavy vehicle driving experience.<br /> Good knowledge of UAE roads and major locations.<br /> Clean driving record with strong road-safety awareness.<br /> Ability to handle loading and unloading procedures when required.<br /> Responsible, punctual, and physically fit.<br /> Good communication skills.<br /> UAE experience is preferred.</p> <p>Interested candidates may submit their updated CV to: info.aljamal.travelandtourism@gmail.com</p>

<h2 class="h5">Job description</h2> <div class="t-break" data-jb-field="description"> <p><b>Title:</b></p><br><br>Job Title: Lead Commissioning Engineer (Mechanical/Piping) – Offshore, WHT’s, Platform, Subsea Cable<br><br><p><b><i>Belong, Connect, Grow, with KBR!</i></b></p><br><br><p><b><i>The KBR team of teams delivers future-forward science, technology and engineering solutions and mission-critical services that help governments and companies around the world accomplish their most important objectives, while also helping achieve their sustainability goals. KBR Sustainable Technology Solutions provides holistic and value-added solutions across the entire asset life cycle. These include world-class licensed process technologies, differentiated advisory services, deep technical domain expertise, energy transition solutions, high-end design and engineering capabilities, and smart solutions to optimize planned and operating assets.</i></b></p><br><br><p><b><u>&nbsp;<span>Job Title: Lead Commissioning Engineer (Mechanical/Piping) – Offshore, WHT’s, Platform, Subsea Cable</span></u></b></p><br><br><p>KBR is growing its Project Management Consultancy (PMC) team for an exciting, high‑profile offshore development in Abu Dhabi. The ADNOC PMC project role would be based initially in Contractors Office/ Fabrication Yard Office in Abu Dhabi for some time and then will later move to Offshore Site on 6 weeks on/ 3 weeks off rotation.</p><br><br><p><b>Job Purpose</b></p><br><br><p>The <b>Lead Commissioning Engineer (Mechanical/Piping)</b> is responsible for planning, coordinating, and leading all Mechanical and Piping commissioning activities for offshore and onshore Oil &amp; Gas projects, ensuring safe, efficient, and compliant system handover from Construction to Operations.</p><br><br><p>The role provides technical leadership during pre-commissioning, commissioning, start-up, performance testing, and handover phases, ensuring that mechanical and piping systems are tested, commissioned, and integrated in accordance with project specifications, operational requirements, HSE standards, and client expectations.</p><br><br><p>The position serves as the focal point between Engineering, Construction, Commissioning, Operations, Vendors, and Client representatives throughout project execution.</p><br><br><p><b>Key Responsibilities</b></p><br><br><p><b>Commissioning Leadership</b></p><br><br><ul><li>Lead Mechanical and Piping commissioning activities from system completion through start-up and final handover.</li><li>Develop and implement commissioning strategies, execution plans, procedures, and schedules.</li><li>Coordinate multidisciplinary commissioning activities to ensure seamless system integration.</li><li>Manage commissioning engineers, supervisors, technicians, and contractor personnel.</li><li>Ensure commissioning targets and project milestones are achieved safely and efficiently.</li></ul><p><b>Pre-Commissioning Management</b></p><br><br><ul><li>Plan and supervise pre-commissioning activities including:<ul><li>Mechanical Completion Verification</li><li>System Walkdowns</li><li>Line Checking</li><li>Flushing and Cleaning</li><li>Air Blowing</li><li>Water Flushing</li><li>Hydrostatic Testing</li><li>Pneumatic Testing</li><li>Leak Testing</li><li>Drying and Preservation Activities</li></ul></li><li>Verify readiness for commissioning and start-up activities.</li><li>Ensure punch list identification and closure processes are effectively managed.</li></ul><p><b>Mechanical &amp; Piping Commissioning</b></p><br><br><p>Coordinate commissioning activities for:</p><br><br><ul><li>Process Piping Systems</li><li>Utility Piping Systems</li><li>Wellhead Facilities</li><li>Offshore Platforms and Topsides</li><li>Wellhead Towers (WHTs)</li><li>Jackets and Bridges</li><li>Subsea Tie-In Supports</li><li>Pressure Vessels</li><li>Heat Exchangers</li><li>Pumps</li><li>Compressors</li><li>Tanks</li><li>Filters and Strainers</li><li>Pigging Facilities</li><li>Mechanical Packages</li><li>Safety Relief Systems</li><li>Produced Water Systems</li><li>Firewater Systems</li><li>HVAC Mechanical Systems</li></ul><p><b>Start-Up &amp; Operational Readiness</b></p><br><br><ul><li>Lead system energization and start-up activities.</li><li>Develop commissioning sequences and start-up procedures.</li><li>Coordinate operational readiness reviews.</li><li>Support performance testing and system acceptance activities.</li><li>Ensure all systems meet design intent and operational requirements.</li><li>Facilitate smooth transfer of facilities to Operations.</li></ul><p><b>Interface &amp; Coordination</b></p><br><br><ul><li>Coordinate with Engineering, Construction, QA/QC, Operations, HSE, Vendors, and Client teams.</li><li>Participate in commissioning meetings, readiness reviews, and management progress sessions.</li><li>Interface with package vendors during testing, start-up, and troubleshooting activities.</li><li>Resolve technical issues impacting commissioning schedules and system performance.</li></ul><p><b>Mechanical Completion &amp; Handover</b></p><br><br><ul><li>Manage Mechanical Completion (MC) activities and certification processes.</li><li>Review and verify system completion dossiers.</li><li>Ensure timely closure of punch items and deficiencies.</li><li>Coordinate turnover packages and handover documentation.</li><li>Facilitate Final Acceptance and project close-out activities.</li></ul><p><b>HSE Responsibilities</b></p><br><br><ul><li>Ensure all commissioning activities comply with project HSE requirements and company procedures.</li><li>Lead commissioning risk assessments, SIMOPS reviews, and Job Safety Analysis (JSA) activities.</li><li>Ensure proper implementation of Permit-to-Work (PTW) systems.</li><li>Promote a strong safety culture during commissioning and start-up phases.</li><li>Participate in incident investigations and implementation of corrective actions.</li></ul><p><b>Quality Assurance</b></p><br><br><ul><li>Verify compliance with project specifications, commissioning procedures, and industry standards.</li><li>Review test records, commissioning reports, and completion documentation.</li><li>Ensure proper documentation of commissioning results and system performance.</li><li>Support quality audits and client inspections.</li><li>Ensure accurate as-built and turnover records are maintained.</li></ul><br><p><b>Qualifications</b></p><br><br><p><b>Education</b></p><br><br><ul><li>Bachelor's Degree in Mechanical Engineering or related Engineering discipline.</li></ul><p><b>Preferred Certifications</b></p><br><br><ul><li>PMP Certification</li><li>BOSIET/HUET (for Offshore Projects)</li><li>NEBOSH or Equivalent HSE Certification</li><li>Completions &amp; Commissioning Management Certification (Preferred)</li></ul><br><p><b>Experience</b></p><br><br><ul><li>Minimum <b>18- 22 years</b> of experience in Mechanical and Piping Commissioning within Oil &amp; Gas, Petrochemical, Refining, LNG, or Offshore EPC/EPCI projects.</li><li>Minimum <b>5 years</b> in a Lead Commissioning Engineer or Senior Commissioning role.</li><li>Proven experience in:<ul><li>Offshore Platforms and Topsides</li><li>Wellhead Towers (WHTs)</li><li>Jackets and Bridges</li><li>Process Facilities</li><li>Water Injection Systems</li><li>Utility Systems</li><li>Mechanical Packages</li><li>Brownfield Modifications and Tie-Ins</li></ul></li><li>Experience supporting pre-commissioning, commissioning, start-up, and operational handover phases.</li><li>Previous ADNOC, Saudi Aramco, QatarEnergy, or major operator project experience is preferred.</li></ul><br><br><br> </div>

<p>A transport and logistics operation in Dubai is hiring a Heavy Vehicle Driver to handle the safe transportation of goods, materials, and equipment using heavy vehicles. The ideal candidate should have strong road knowledge, responsible driving habits, and the ability to follow scheduled routes and delivery requirements.</p> <p>Key Responsibilities<br /> Operate heavy vehicles safely for transportation and delivery assignments.<br /> Transport goods, materials, and equipment between designated locations.<br /> Follow assigned routes, schedules, and delivery instructions.<br /> Conduct basic vehicle inspections before starting each trip.<br /> Check fuel, tyres, brakes, lights, and other essential vehicle components.<br /> Ensure cargo is properly loaded, secured, and protected during transportation.<br /> Complete delivery notes, trip sheets, and other required records.<br /> Coordinate with the transport supervisor regarding routes and schedules.<br /> Report accidents, vehicle faults, delays, or cargo-related issues immediately.<br /> Follow UAE traffic laws, road safety regulations, and company procedures.<br /> Maintain the cleanliness and general condition of the assigned vehicle.<br /> Assist with loading and unloading activities when required.<br /> Requirements<br /> Valid UAE Heavy Vehicle Driving Licence.<br /> Previous experience as a Heavy Vehicle Driver is preferred.<br /> Good knowledge of Dubai and UAE roads.<br /> Familiarity with safe cargo handling and transportation procedures.<br /> Basic understanding of heavy vehicle maintenance and safety checks.<br /> Good communication and coordination skills.<br /> Responsible, punctual, and safety-conscious attitude.<br /> Physically fit and capable of handling transportation-related duties.<br /> Ability to work flexible hours according to operational requirements.<br /> UAE or GCC heavy vehicle driving experience will be an advantage.</p> <p>Interested candidates may submit their updated CV to the email:edu@jamalschools.com</p>

<ul><li>Performs skilled mechanical maintenance at an advanced level on typical mechanical equipment of Offshore Oil &amp;amp; Gas Installations. Leads and directs assigned crew consisting of related crafts as well as participates in the crew’s tasks. (Work includes but is not limited to Gas turbines, diesel engines, air compressors, various pumps, fire fighting equipment, various pipelines, gas plant &amp;amp; incinerator and includes all mechanical maintenance including fabrication and light machining jobs etc.).</li></ul><p><strong>KEY ACCOUNTABILITIES</strong></p><ul><li>Performs, leads and gives directions to crew, consisting of Mechanical</li><li>Technicians and Fitters during preventive /corrective/ breakdown/ shutdown/turnaround maintenance in the Super Complex.</li><li>Receives work request from Mechanical Supervisor. Attends directly to requests from various Sections in the Super Complex for Maintenance of different static and rotating mechanical equipment like pumps, compressors, heat exchangers, valves, vessels, fire fighting system etc.</li><li>Disassembles, assembles, observes, repairs, tests, collects data and prepares reports etc on equipment, as tasks related to maintenance.</li><li>Performs installation and alignment of equipment such as pumps, compressors, gas turbines, static equipment etc using relevant tools including computerized laser alignment tools.</li><li>Installs, removes, inspects and repairs mechanical spare parts like bearings, seals etc on typical mechanical equipment.</li><li>Performs and gives directions to crew during major overhaul of equipment with or without external contractors and vendors.</li><li>Works on various equipment in the plant as well as in workshop.</li><li>Uses and ensures use of proper tools and tackles on the job by assigned crew.</li><li>Carries out periodic pre-use inspection of tools and special tools, repairs, overhauls and tests them when required.</li><li>Learns from the methods and errors and recommends to the supervisor on ways of continuous improvement.</li><li>Assists the supervisor to improve the productivity of crew by making relevant recommendations as well as to achieve cost effective maintenance.</li></ul>

<p>A construction company is looking for an experienced MEP Supervisor to oversee mechanical, electrical, and plumbing activities across construction projects and ensure work is completed safely, efficiently, and according to project specifications.</p> <p>Key Responsibilities<br /> Supervise daily MEP installation and maintenance activities<br /> Coordinate mechanical, electrical, and plumbing works with site teams<br /> Monitor work progress and ensure compliance with approved drawings and specifications<br /> Coordinate with engineers, contractors, and other site supervisors<br /> Inspect completed work and identify quality or technical issues<br /> Ensure materials and equipment are available as required<br /> Monitor site safety procedures and ensure workers follow HSE requirements<br /> Prepare progress updates and report site issues to management<br /> Assist in coordinating inspections, testing, and commissioning activities<br /> Applicants may send cv via email address globalfahli@gmail.com</p>

<p>A construction company is looking for an experienced MEP Supervisor to oversee mechanical, electrical, and plumbing activities across construction projects and ensure work is completed safely, efficiently, and according to project specifications.</p> <p>Key Responsibilities<br /> Supervise daily MEP installation and maintenance activities<br /> Coordinate mechanical, electrical, and plumbing works with site teams<br /> Monitor work progress and ensure compliance with approved drawings and specifications<br /> Coordinate with engineers, contractors, and other site supervisors<br /> Inspect completed work and identify quality or technical issues<br /> Ensure materials and equipment are available as required<br /> Monitor site safety procedures and ensure workers follow HSE requirements<br /> Prepare progress updates and report site issues to management<br /> Assist in coordinating inspections, testing, and commissioning activities<br /> Applicants may send cv via email address globalfahli@gmail.com</p>

<h2 class="h5">Job description</h2> <div class="t-break" data-jb-field="description"> <p><strong>Job Description: Civil Site Engineer – Substation Projects (UAE)</strong> ???</p><br><p><strong>Position Title:</strong> Civil Site Engineer<br><strong>Project Type:</strong> Electrical Substation Projects (132kV / 220kV / 400kV and Distribution Substations)<br><strong>Location:</strong> United Arab Emirates (Abu Dhabi, Dubai, Northern Emirates)<br><strong>Reporting To:</strong> Project Manager / Senior Civil Engineer / Construction Manager</p><br>1. Job Purpose ?<p>The Civil Site Engineer for substation projects is responsible for planning, supervising, and executing civil construction activities at electrical substations in compliance with project specifications, authority requirements, safety standards, and quality procedures. The role ensures that all civil works such as foundations, cable trenches, control buildings, equipment plinths, boundary walls, roads, and drainage systems are executed efficiently, safely, and within schedule.</p><br><p>The Civil Site Engineer acts as the key interface between the design team, subcontractors, consultants, and project management to ensure smooth project execution. The position requires strong coordination skills, technical knowledge of substation civil works, and familiarity with UAE authority standards such as ADDC, AADC, DEWA, SEWA, FEWA/EtihadWE, and TRANSCO.</p><br>2. Key Responsibilities ??A. Site Execution &amp; Supervision<ul><li>Supervise day-to-day civil construction activities at substation sites.</li><li>Ensure works are carried out as per approved drawings, method statements, and project specifications.</li><li>Coordinate with subcontractors for execution of foundations, cable trenches, transformer bunds, GIS buildings, control rooms, and internal roads.</li><li>Monitor excavation, backfilling, compaction, and concrete works.</li><li>Ensure proper levels and alignment for equipment foundations.</li><li>Supervise installation of underground utilities and drainage systems.</li><li>Verify rebar placement, formwork, embedment installation, and concrete pouring.</li><li>Check compliance with approved ITPs (Inspection and Test Plans).</li><li>Ensure proper curing and protection of concrete structures.</li></ul>B. Planning &amp; Scheduling ?<ul><li>Prepare weekly and daily work plans in coordination with the construction manager.</li><li>Monitor progress against project schedule and highlight delays.</li><li>Coordinate with procurement team for material delivery.</li><li>Ensure manpower and equipment availability for planned activities.</li><li>Assist in preparation of look-ahead schedules.</li><li>Support recovery plans in case of project delays.</li></ul>C. Coordination with Stakeholders ?<ul><li>Liaise with consultants for inspections and approvals.</li><li>Coordinate with electrical and mechanical teams for interface works.</li><li>Communicate with surveyors for setting out works.</li><li>Attend site coordination meetings with contractors and clients.</li><li>Resolve site technical issues in consultation with design team.</li><li>Coordinate with QA/QC engineers for inspections.</li></ul>D. Quality Control &amp; Assurance ?<ul><li>Ensure all materials comply with approved submittals.</li><li>Conduct site checks before consultant inspections.</li><li>Monitor concrete cube testing and compaction tests.</li><li>Ensure compliance with authority standards (ADDC, DEWA, etc.).</li><li>Maintain site quality records.</li><li>Ensure corrective actions for non-conformance reports (NCRs).</li><li>Follow approved method statements.</li></ul>E. Health, Safety &amp; Environment (HSE) ?<ul><li>Enforce safety procedures at site.</li><li>Conduct daily toolbox talks with workforce.</li><li>Ensure use of PPE by all workers.</li><li>Monitor safe excavation practices.</li><li>Ensure barricading of open trenches and pits.</li><li>Coordinate lifting operations for heavy equipment foundations.</li><li>Report incidents and near misses.</li><li>Ensure compliance with UAE HSE regulations.</li></ul>F. Survey &amp; Setting Out ?<ul><li>Verify benchmarks and reference points.</li><li>Coordinate with surveyor for layout of buildings and foundations.</li><li>Check finished levels of cable trenches and roads.</li><li>Ensure proper slope for drainage systems.</li><li>Verify as-built coordinates.</li></ul>G. Documentation &amp; Reporting ?<ul><li>Prepare daily progress reports.</li><li>Maintain site diaries.</li><li>Record manpower and equipment deployment.</li><li>Prepare inspection requests (IRs).</li><li>Track material delivery and usage.</li><li>Maintain drawing register.</li><li>Prepare red-mark drawings for as-built documentation.</li><li>Assist in preparation of monthly progress reports.</li></ul>3. Scope of Civil Works in Substation Projects ?<p>The Civil Site Engineer will typically handle the following works:</p><br><ul><li>Substation control building construction</li><li>GIS building civil works</li><li>Transformer foundations</li><li>Reactor foundations</li><li>Equipment plinths</li><li>Cable trenches and troughs</li><li>Cable basement works</li><li>Oil containment bunds</li><li>Boundary wall and fencing</li><li>Internal asphalt/concrete roads</li><li>Stormwater drainage systems</li><li>Earthing pits and chambers</li><li>Water tanks and pump rooms</li><li>Security buildings</li><li>Equipment gantry foundations</li><li>Firefighting water reservoir structures</li><li>Duct banks and underground sleeves</li></ul>4. Technical Requirements ?<ul><li>Good understanding of substation layout drawings.</li><li>Knowledge of reinforced concrete structures.</li><li>Experience in heavy equipment foundations.</li><li>Understanding of soil conditions and ground improvement.</li><li>Familiarity with cable trench construction.</li><li>Knowledge of concrete mix design and testing.</li><li>Ability to read IFC drawings and shop drawings.</li><li>Understanding of UAE construction standards.</li><li>Experience with excavation and shoring systems.</li><li>Knowledge of waterproofing and joint sealing.</li></ul>5. Qualification Requirements ?<ul><li>Bachelor’s Degree in Civil Engineering.</li><li>Minimum 4–8 years of experience in civil construction.</li><li>At least 2–3 years in substation projects in UAE.</li><li>Experience in high voltage substations preferred.</li><li>Knowledge of authority standards (DEWA/ADDC/TRANSCO).</li><li>UAE driving license preferred.</li></ul>6. Skills &amp; Competencies ?<ul><li>Strong technical knowledge of civil works.</li><li>Good communication skills.</li><li>Ability to coordinate multiple teams.</li><li>Problem-solving capability.</li><li>Planning and organizational skills.</li><li>Leadership abilities.</li><li>Time management skills.</li><li>Attention to detail.</li><li>Ability to work under pressure.</li><li>Familiarity with AutoCAD drawings.</li></ul>7. Software Knowledge ?<ul><li>AutoCAD (basic review)</li><li>MS Excel</li><li>MS Project / Primavera (basic)</li><li>MS Word</li><li>Inspection management systems</li><li>ERP systems (preferred)</li></ul>8. Key Performance Indicators (KPIs) ?<ul><li>Progress vs schedule achievement</li><li>Quality compliance rate</li><li>Number of NCRs</li><li>Safety compliance</li><li>Productivity of subcontractors</li><li>Material wastage control</li><li>Inspection approval rate</li><li>Project milestone achievement</li></ul>9. Working Conditions ?<ul><li>Site-based role in outdoor environment.</li><li>Work in high temperature conditions typical in UAE.</li><li>Coordination with multiple subcontractors.</li><li>Occasional extended working hours to meet deadlines.</li><li>Travel between multiple substation sites may be required.</li></ul>10. Responsibilities During Project Phases ?Mobilization Phase<ul><li>Review drawings and specifications.</li><li>Participate in site handover.</li><li>Coordinate site setup.</li><li>Verify benchmarks.</li></ul>Construction Phase<ul><li>Supervise all civil works.</li><li>Coordinate inspections.</li><li>Monitor progress.</li><li>Ensure quality compliance.</li></ul>Testing &amp; Commissioning Phase<ul><li>Support electrical team.</li><li>Complete finishing works.</li><li>Clear punch list items.</li><li>Assist in handover documentation.</li></ul>Project Close-Out<ul><li>Prepare as-built drawings.</li><li>Close NCRs.</li><li>Finalize documentation.</li><li>Assist in project handover.</li></ul>11. Preferred Experience in UAE Substation Authorities ?<p>Experience in projects under:</p><br><ul><li>TRANSCO</li><li>ADDC / AADC</li><li>DEWA</li><li>SEWA</li><li>EtihadWE (FEWA)</li><li>ADNOC substations</li></ul>12. Reporting Structure ?<p>Civil Site Engineer reports to:</p><br><ul><li>Construction Manager</li><li>Project Manager</li><li>Senior Civil Engineer</li></ul><p>Coordinates with:</p><br><ul><li>Electrical Engineers</li><li>QA/QC Engineers</li><li>HSE Engineers</li><li>Surveyors</li><li></li></ul> </div>

<h2 class="h5">Job description</h2> <div class="t-break" data-jb-field="description"> <p><strong>Job Description:</strong></p><br><p>The NSSTC is looking to hire Mechanical Engineer to support the development of the NSSTC facility, to design and develop ground support and test equipment, and to create electro-mechanical hardware intended for both ground and space operation. You’ll be working as part of a team designing and building CubeSats and Small Spacecraft as part of the center’s charter. As an engineer you will be asked to perform a variety of tasks related to the development of the center including (but not limited to) support of the facilities development; test equipment development; and design, analysis, assembly, test, and verification/validation of performance of ground and space-based hardware and software. The ability to work with students at UAE University as a mentor is required. Travel may be required – both domestic and international. The position is located at the NSSTC facility in Al Ain. Compensation based on experience level. Tasks and Responsibilities: • Interfacing with a multi-disciplinary team including professionals, faculty, graduate and undergraduate students • Documenting interfaces and requirements • Designing discipline-specific components for space flight applications • Modeling and analyzing designs of ground and space hardware • Performing other engineering tasks (analyzing mass properties, structure development, harness routing, simple stress and/or thermal analysis, design development, production planning, drawing creation, etc.) • Support assembly and integration operation </p><br><p><strong>Minimum Qualifications:</strong></p><br><p>• Bachelor or higher degree in Mechanical Engineering </p><br><p><strong>Preferred Qualifications:</strong></p><br><p> • Demonstrated experience with CAD tools • Familiarity with designing and packaging electro-mechanical systems for the space environment • Cleanroom experience </p><br> </div>

<ul><li>Assist in the design and drafting of HVAC systems, including ductwork, piping, and equipment layout, ensuring compliance with project specifications and building codes.</li><li>Support senior engineers in performing load calculations and energy modeling to optimize system performance and efficiency.</li><li>Conduct site visits to gather information, inspect installations, and troubleshoot issues, documenting findings and recommendations.</li><li>Prepare technical documentation, such as equipment schedules, submittal reviews, and project reports, with a focus on accuracy and clarity.</li></ul><p><strong>Desired Candidate Profile</strong></p><ul><li>Bachelor's degree in Mechanical Engineering or a related field from an accredited institution.</li><li>Possession of an Engineer-in-Training (EIT) certification is highly preferred.</li><li>0-2 years of relevant internship or co-op experience in HVAC design or mechanical systems.</li><li>Familiarity with HVAC industry standards such as ASHRAE, SMACNA, and local building codes.</li></ul>

<h2 class="h5">Job description</h2> <div class="t-break" data-jb-field="description"> <p><b>Job Description:</b></p><p>AL ENSHAA Electromechanical Contracting L.L.C. is looking for an experienced <b>QA/QC Engineer – MEP</b> with <b>UAE experience</b> to ensure all Mechanical, Electrical, and Plumbing (MEP) works comply with project specifications, standards, and quality requirements.</p><p><b>Key Responsibilities:</b></p><ul><li>Implement and monitor QA/QC procedures for MEP works.</li><li>Conduct inspections and prepare inspection reports.</li><li>Ensure compliance with project specifications, applicable codes, and quality standards.</li><li>Coordinate with site, engineering, consultant, and client teams.</li><li>Review material submittals, method statements, and inspection requests.</li><li>Monitor site activities to ensure quality requirements are consistently achieved.</li><li>Maintain QA/QC documentation and quality records throughout the project lifecycle.</li></ul><p><b>Requirements:</b></p><ul><li>Proven experience as a QA/QC Engineer in MEP projects <b>within the UAE</b>.</li></ul><p><b>Job Type:</b> Full-time</p><p><b>Work Location:</b> UAE (On-site)</p><p><b>Preference will be given to candidates who are available to join immediately.</b></p><ul><li>Strong knowledge of MEP systems, quality standards, and local regulations.</li><li>Familiar with inspections, testing, commissioning, and quality documentation.</li><li>Good communication, coordination, and reporting skills.</li><li>Ability to work independently and manage multiple tasks effectively.</li></ul><p><br></p> </div><h2 class="h5">Skills</h2> <div data-jb-field="skills"><p>QA/QC Engineering (MEP)</p><p>Mechanical, Electrical &amp; Plumbing (MEP)</p><p>Quality Assurance &amp; Quality Control</p><p>Site Inspection</p><p>Testing &amp; Commissioning</p><p>Material Submittals</p><p>Method Statements</p><p>Inspection Requests (IR)</p><p>Quality Documentation</p><p>UAE Building Codes &amp; Regulations</p><p>Communication Skills</p><p>Coordination Skills</p><p>Reporting</p><p>Time Management</p><p>Problem Solving</p><p>Microsoft Office</p></div>

<section><p class="heading jdMain">Job Description</p><p class="heading">Roles &amp; Responsibilities</p><div class="paragraph"><ul><li><p>Lead and supervise all mechanical site works including HVAC, plumbing, and firefighting systems for high‑rise projects.</p></li><li><p>Coordinate with consultants, contractors, and project teams to ensure compliance with design, codes, and QA/QC standards.</p></li><li><p>Review and approve shop drawings, material submittals, and method statements.</p></li><li><p>Monitor site progress, resolve technical issues, and ensure timely execution of mechanical works.</p></li><li><p>Enforce HSE standards and support testing, commissioning, and project handover.</p></li></ul></div></section><section><p class="heading">Desired Candidate Profile</p><p class="paragraph"></p><ul><li><p>Bachelor's degree in Mechanical Engineering or a related field.</p></li><li><p>Minimum of 10 years experience in MEP High rise building construction projects. </p></li><li><p>UAE experience is must. </p></li><li><p>Authority Approvals will be preferred.</p></li><li><p>Immediate joiners will be preferred. </p></li></ul><p></p></section>

<h2 class="h5">Job description</h2> <div class="t-break" data-jb-field="description"> <p>Job Summary</p><p>&nbsp;</p><p>We are looking for a qualified and motivated Mechanical &nbsp;Engineer to join our growing MEP team in Dubai. The ideal candidate must have solid experience in HVAC and Plumbing systems, with the ability to independently manage site execution, coordinate with consultants and clients, and ensure timely completion of projects in accordance with UAE standards.</p><p>&nbsp;</p><p>Minimum Requirements</p><p>&nbsp;</p><p>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;Bachelor's Degree in Mechanical Engineering.</p><p>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;5–7 years of UAE experience in MEP contracting.</p><p>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;Thorough knowledge of complete HVAC and Plumbing &nbsp;systems, including installation, testing, commissioning, and maintenance.</p><p>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;Good understanding of UAE codes, Dubai Municipality, and project specifications.</p><p>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;Valid UAE Driving Licence (mandatory).</p><p>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;Ability to read and interpret MEP drawings and coordinate with other disciplines.</p><p>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;Strong knowledge of material take-offs, site supervision, and quality control.</p><p>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;Good communication and coordination skills.</p><p>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;Proficient in Microsoft Office and AutoCAD. Knowledge of Revit is an advantage.</p> </div><h2 class="h5">Skills</h2> <div data-jb-field="skills"><p>Key Responsibilities</p><p>&nbsp;</p><p>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;Supervise and manage HVAC and Plumbing installation works on site.</p><p>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;Coordinate with consultants, clients, subcontractors, and suppliers.</p><p>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;Ensure work is executed as per approved drawings, specifications, and project schedules.</p><p>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;Prepare material requisitions and monitor material usage.</p><p>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;Attend site meetings and resolve technical issues.</p><p>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;Conduct inspections, testing, and commissioning activities.</p><p>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;Ensure compliance with quality, health, safety, and environmental requirements.</p><p>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;Prepare progress reports and maintain project documentation.</p><p><br></p></div>

Company Description Kaskada is an engineering-focused organization specializing in delivering high-quality building services and infrastructure solutions. The company emphasizes technical excellence, reliable project delivery, and close collaboration with stakeholders across the construction lifecycle. Kaskada’s teams work with modern engineering tools and industry standards to design efficient, sustainable, and safe systems for commercial and residential projects. Professionals joining Kaskada can expect a performance-driven environment with opportunities to contribute to impactful projects and develop their technical expertise.<br>Role Description The Mechanical, Electrical, and Plumbing (MEP) Engineer will be responsible for designing, reviewing, and coordinating building services systems for projects based in Dubai, United Arab Emirates. This full-time, on-site role includes preparing and updating MEP drawings and specifications, conducting load calculations, and ensuring designs comply with relevant codes and standards. The engineer will collaborate with architects, structural engineers, contractors, and suppliers to resolve technical issues and maintain alignment between disciplines. Daily tasks involve site inspections, monitoring installation progress, verifying workmanship and materials, and supporting testing, commissioning, and handover activities. The role also includes preparing technical reports, responding to RFIs, and supporting value engineering initiatives to optimize performance, cost, and sustainability.<br>Qualifications<br> Candidates should possess strong Mechanical, Electrical, and Plumbing (MEP) engineering skills, including experience in integrated building services design. Candidates should possess skills in Plumbing and Building Services, with the ability to design and review water supply, drainage, and related systems. Candidates should possess skills in Electrical Engineering and Building Services, including power distribution, lighting, and low-voltage systems. Candidates should possess skills in MEP Coordination, ensuring effective collaboration among mechanical, electrical, and plumbing disciplines and alignment with architectural and structural plans. Relevant bachelor’s degree in Mechanical, Electrical, or Building Services Engineering (or closely related field); professional certification or membership in an engineering body is an advantage. Experience with industry-standard design software and tools (e.g., Auto CAD, Revit, or similar BIM platforms; calculation software for HVAC, electrical, and plumbing systems). Knowledge of international and regional building codes, standards, and regulations applicable in the UAE. Strong analytical, problem-solving, and technical report-writing skills, with attention to detail and quality. Ability to work on-site in Dubai, manage multiple projects or tasks, and communicate effectively with multidisciplinary teams.

<ul><li><p>Conduct inspections of lifting equipment and lifting accessories</p></li><li><p>Inspect cranes, hoists, slings, shackles, hooks and other lifting accessories</p></li><li><p>Conduct inspections of earth-moving machinery, including excavators, loaders, backhoe loaders, bulldozers, graders, rollers and dumpers</p></li><li><p>Perform visual, functional and operational inspections according to approved procedures</p></li><li><p>Verify equipment identification, documents, safe working load, safety devices and general condition</p></li><li><p>Identify defects, unsafe conditions and non-conformities</p></li><li><p>Prepare clear and accurate inspection reports and certificates</p></li><li><p>Maintain proper inspection records, photographs and supporting evidence</p></li><li><p>Ensure inspection tools and measuring equipment have valid calibration</p></li><li><p>Follow company procedures, applicable standards and client safety requirements</p></li><li><p>Maintain impartiality, confidentiality and professional conduct</p></li><li><p>Report immediately any equipment presenting a serious safety risk</p></li><li><p>Coordinate with clients, site representatives and the Technical Manager</p></li></ul><p><strong>Desired Candidate Profile</strong></p><ul><li><p>Bachelor’s degree in Mechanical Engineering – mandatory</p></li><li><p>Minimum 2 years of relevant inspection experience</p></li><li><p>Practical experience in inspecting lifting equipment and lifting accessories</p></li><li><p>Practical experience in inspecting earth-moving machinery</p></li><li><p>Knowledge of applicable inspection standards, safety requirements and manufacturer instructions</p></li><li><p>Ability to identify defects and prepare accurate inspection reports</p></li><li><p>LEEA qualification will be an advantage</p></li><li><p>Knowledge of ISO/IEC 17020 requirements will be an advantage</p></li><li><p>Good English communication and technical report-writing skills</p></li><li><p>Able to work independently at different client sites</p></li><li><p>Immediate joiners will be preferred</p></li></ul>

<p>We are seeking a highly skilled and experienced Static & Thermal Design Engineer with strong expertise in the design, analysis, detailing, and costing of pressure vessels, atmospheric storage tanks, thermal energy storage systems, silos, heat exchangers, and skid-mounted process equipment.</p><p>The candidate shall possess hands-on experience in mechanical and thermal design software including PV Elite, HTRI, ASPEN, AutoCAD, and 3D modeling platforms. The role requires the ability to independently perform design calculations, prepare fabrication drawings, generate BOQ/cost estimates, and coordinate with fabrication, procurement, and project teams.</p><p>Key Responsibilities Mechanical & Static Design</p><ul><li><p>Design and detailed engineering of:</p></li><li><p>Pressure Vessels</p></li><li><p>Heat Exchangers</p></li><li><p>Atmospheric Storage Tanks</p></li><li><p>Thermal Energy Storage (TES) Tanks</p></li><li><p>Silos and Process Vessels</p></li><li><p>Buffer Tanks and Calorifiers</p></li><li><p>Degassing Units and Skid Packages</p></li><li><p>Compressed Air</p></li><li><p>Cryogenic Package</p></li><li><p>LPG and Fuel System</p></li><li><p>Perform mechanical calculations in accordance with:</p></li><li><p>ASME Section VIII Div. 1 & 2</p></li><li><p>API 650 / API 620</p></li><li><p>TEMA</p></li><li><p>ANSI / ASTM standards</p></li><li><p>Local and international codes</p></li></ul><p>Prepare:</p><ul><li><p>Design calculations</p></li><li><p>Mechanical datasheets</p></li><li><p>General Arrangement Drawings (GA)</p></li><li><p>Fabrication drawings</p></li><li><p>Nozzle orientation drawings</p></li><li><p>Bill of Materials (BOM)</p></li><li><p>Material Take-Off (MTO)</p></li></ul><p>Perform:</p><ul><li><p>Shell thickness calculations</p></li><li><p>Nozzle reinforcement calculations</p></li><li><p>Wind and seismic analysis</p></li><li><p>Saddle/support design</p></li><li><p>Lifting and transportation analysis</p></li></ul><p>Thermal Design Responsibilities</p><ul><li><p>Perform thermal calculations and thermal sizing for:</p></li><li><p>Shell & Tube Heat Exchangers</p></li><li><p>Plate Heat Exchangers</p></li><li><p>TES Systems</p></li><li><p>Chilled Water Systems</p></li><li><p>Hot Water Systems</p></li><li><p>Glycol Cooling Systems</p></li></ul><p>Use software including:</p><ul><li><p>HTRI</p></li><li><p>ASPEN HYSYS / ASPEN Plus</p></li><li><p>PV Elite</p></li><li><p>Compress / equivalent software</p></li><li><p>Validate:</p></li><li><p>Heat transfer performance</p></li><li><p>Pressure drop calculations</p></li><li><p>Flow velocity analysis</p></li><li><p>Thermal efficiency</p></li><li><p>Energy balance calculations</p></li><li><p>Coordinate thermal design with process and mechanical requirements.</p></li></ul><p>Drafting & 3D Engineering</p><ul><li><p>Generate detailed engineering drawings using:</p></li><li><p>AutoCAD</p></li><li><p>SolidWorks / Inventor / equivalent 3D software</p></li><li><p>Develop:</p></li><li><p>3D skid layouts</p></li><li><p>Piping arrangements</p></li><li><p>Structural interface layouts</p></li><li><p>Equipment assembly drawings</p></li><li><p>Production/fabrication drawings</p></li><li><p>Coordinate with fabrication team for manufacturability and optimization.</p></li></ul><p>Estimation & BOQ Preparation</p><ul><li><p>Prepare:</p></li><li><p>BOQ (Bill of Quantities)</p></li><li><p>Cost estimation</p></li><li><p>Material costing</p></li><li><p>Weight calculations</p></li><li><p>Tender technical submissions</p></li><li><p>Coordinate with procurement for:</p></li><li><p>Material specifications</p></li><li><p>Vendor data review</p></li><li><p>Technical bid evaluations</p></li><li><p>Support commercial and sales teams during tendering stage.</p></li></ul><p>Required Skills & Competencies</p><ul><li><p>Strong understanding of:</p></li><li><p>Pressure vessel codes and standards</p></li><li><p>Thermal system engineering</p></li><li><p>Static equipment design</p></li><li><p>Fabrication processes</p></li><li><p>Welding standards and material selection</p></li><li><p>Ability to independently execute complete design packages.</p></li><li><p>Strong analytical and problem-solving capabilities.</p></li><li><p>Excellent knowledge of engineering documentation and QA/QC requirements.</p></li><li><p>Good communication and coordination skills.</p></li></ul><p>Software Requirements</p><br><p><strong>Desired Candidate Profile</strong></p><p>Mandatory proficiency in:</p><ul><li><p>PV Elite</p></li><li><p>HTRI</p></li><li><p>ASPEN HYSYS / ASPEN Plus</p></li><li><p>AutoCAD</p></li><li><p>MS Excel</p></li><li><p>3D Modeling Software (SolidWorks / Inventor / equivalent)</p></li></ul><p>Preferred:</p><ul><li><p>ANSYS</p></li><li><p>Compress</p></li><li><p>Tekla / Plant 3D</p></li><li><p>Revit</p></li><li><p>CFD or FEA software experience</p></li></ul><p>Educational Qualification</p><ul><li><p>Bachelor’s Degree in:</p></li><li><p>Mechanical Engineering</p></li><li><p>Thermal Engineering</p></li><li><p>Process Engineering</p></li><li><p>from a recognized university.</p></li></ul><p>Experience Requirements</p><ul><li><p>Minimum 5 years of relevant experience in:</p></li><li><p>Pressure vessel design</p></li><li><p>Thermal equipment design</p></li><li><p>Static equipment engineering</p></li><li><p>Industrial process equipment manufacturing</p></li><li><p>Experience in HVAC, district cooling, oil & gas, energy, or industrial manufacturing sectors will be an added advantage.</p></li></ul><p>Preferred Candidate Profile</p><ul><li><p>Ability to manage projects independently.</p></li><li><p>Experience in manufacturing/fabrication environment preferred.</p></li><li><p>Knowledge of international design codes and client specifications.</p></li><li><p>Experience in skid package engineering and TES systems is highly desirable.</p></li></ul>

JOB SUMMARYThis position is responsible for the operational condition, maintenance and repair of all medical equipment and mechanical/electrical systems to ensure the safety of patients as well as the staff operating the equipment. This position is also responsible for providing professional levels of customer service to personnel throughout CCAD.<br>PRIMARY JOB DUTIES AND RESPONSIBILITIESConsults with medical or research staff to make sure that equipment functions properly and safely, utilizing knowledge of electronics and medical terminology Repairs, calibrates and maintains group one and group two medical equipment and instrumentation used in the health care delivery field. Inspects, installs and coordinates commissioning of medical and related technical equipment for use by physicians, nurses, scientists or engineers involved in researching, monitoring, diagnosing and treating Services various equipment, such as patient monitors, electrocardiographs, blood gas analyzers, x-ray units, defibrillators, electrosurgical units, anesthesia apparatus, pacemakers, blood pressure transducers, spiro meters, sterilizers, diathermy equipment and other related medical equipment Repairs and maintains equipment using hand tools, test equipment, measuring devices and knowledge of manufacturers’ manuals, troubleshooting techniques and preventive-maintenance schedules Tests medical equipment to ensure patient and staff safety from electrical or mechanical hazards Work with, and directs the activities of, contractors, vendors and outside service technicians, to ensure the appropriate delivery of services<br>QUALIFICATION & EXPERIENCE REQUIREMENTSAssociate’s degree is required. Must have completed training programs from an accredited educational organization in at least two of the following areas: general diagnostic imaging, mammography, radiographic/fluoroscopic imaging, nuclear medicine, CT/MR, ultrasound or PACSMinimum of three to five (3-5) years experience servicing and performing repairs on sophisticated medical equipment Familiarity with and demonstrated proficiency in resolving complex technical problems in biomedical equipment Demonstrated customer support skills and PC competency with knowledge of computer networks Health care industry experience is preferred